Current Classifieds

1978 Pinto Wagon V8
Date: 04/28/2023 03:26 pm
4-14" Chrome Plated Wheels 4 x 108 + 0mm offset with new tires

Date: 09/12/2018 12:33 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
73 Pinto delivery wagon drag car

Date: 02/22/2017 01:58 pm
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm
1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am
sport steering wheeel
Date: 10/01/2020 10:58 pm
1971 Pinto Parting out

Date: 07/06/2018 01:11 pm
Looking for a few parts - TIA
Date: 02/19/2023 12:18 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
1971 Pinto instrument cluster clear bezel WTB
Date: 03/16/2017 10:00 pm
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am

« previous next »
Pages: [1]   Go Down

Author Topic: Front Rim Offset for 15 inch conversion....  (Read 1254 times)

0 Members and 1 Guest are viewing this topic.

Offline niceguynnc

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • Proud 1976 Runabout owner.

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User
Front Rim Offset for 15 inch conversion....
« on: February 10, 2015, 03:14:13 PM »
I just drilled my rear axles to 5x4.5 and ordered the rotor kit for the front to adapt to 5x4.5.  My car is stock and not tubbed. I know the front ball joint is tricky on these cars and the offset has to be right. Also the center circle has to be right too! I want 8 inch wide on the rear and 6 inch on the front. Anyone with 15 inch wheels that can help me get a rim order right i would really appreciate it. Summit could not help me at all.... I am looking at the 4 .5 backspacing on the rear. And as far as the front I have no idea on backspacing due to going to the 15 inch rim diameter..I really want to get the order right the first time. ANY help would be appreciated to the fullest extent! Thanks again in advance!! Greg.
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Front Rim Offset for 15 inch conversion....
« Reply #1 on: February 19, 2015, 10:28:02 PM »
Go to "Wheel Vintiques.com", page 47.  There is a wheel fitment guide that will show where you need to measure.  I also recommend measuring with a straight edge from the face of the rotor where the wheel contacts the rotor to the outermost edge of the top a-arm. That is also a potential contact point of the wheel lip if your backset is too deep.
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Front Rim Offset for 15 inch conversion....
« Reply #2 on: February 20, 2015, 08:03:07 AM »
Anything more than 3 3/4" will drag on the upper control arm. With a 15 X 6 wheel I would go with 2" to 3" back space. 2" would be what I think would fill up the wheel well with that narrow a wheel. If you use too much back space the wheel will look like it came off a FWD car. LOL
Logged
Its better to be a has-been, than a never was.
Pages: [1]   Go Up
« previous next »