Current Classifieds

Wanted early pinto
Date: 10/03/2019 02:42 pm
1972 Pinto SCCA BS race car

Date: 10/23/2018 04:01 pm
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
1978 bobcat 4speed shifter
Date: 11/02/2023 09:51 pm
front end parts
Date: 03/30/2018 12:48 pm
Wanted 71-73 Pinto grill
Date: 03/09/2019 10:45 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
1976 Pinto runabout

Date: 03/28/2017 08:14 pm
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
74 Wagon body parts and a couple of 79 bits

Date: 11/14/2019 04:02 am
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Help, replacement rack and pinion won't fit  (Read 1255 times)

0 Members and 1 Guest are viewing this topic.

Offline nothingtodo

  • Pinto Member
  • **
  • Posts: 49
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Fifth year Anniversary Windows User
Help, replacement rack and pinion won't fit
« on: May 07, 2015, 07:26:34 AM »
Replacing the R&P on my 1979 due to faulty inner tie rods. I bought a replacement manual R&P from Rock Auto and looks fine, but discovered that the rag joint coupler needs a flat ground on the steering input shaft on the R&P and the replacement is perfectly round! Anyone seen this before? Not sure if I should grind a flat on shaft and use it or try to return it and find one that will work. For those of you who have replaced your manual R&P, where did you get yours from?
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Help, replacement rack and pinion won't fit
« Reply #1 on: May 07, 2015, 12:11:58 PM »
I myself have no trouble with putting a flat on but it is timed to make the steering wheel straight ahead and the rack centered end to end. You don't locate it just anywhere.

Flat not being there screams possibly wrong part, I would be double checking EVERYTHING else before I butchered the part to not be able to return it. Look close at the spline all the way around, some look round but one small tooth is missing to do the same as the flat.......... .........and not obvious until you look for it.
Logged

Offline rpaulsel

  • Pinto Driver
  • *
  • Posts: 8
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Mobile User Poll Voter Windows User
Re: Help, replacement rack and pinion won't fit
« Reply #2 on: May 09, 2015, 04:35:14 AM »
I replaced mine on the '76 with a part from Speedway Motors.  It worked perfectly.
Logged
76 Pinto 302 wagon
Pages: [1]   Go Up
« previous next »