Current Classifieds

Wheel cap
Date: 04/25/2022 11:21 pm
Seeking 1971-1973 Rotors
Date: 04/08/2021 12:23 pm
78 fender and hood
Date: 03/23/2021 01:07 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am
71-73 Front Kick Panels
Date: 04/25/2021 07:24 pm
upholstery for bucket seats
Date: 10/30/2018 08:44 am
WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am
Squire trim
Date: 03/28/2018 10:11 am
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm
Interior Parts
Date: 08/07/2017 03:59 pm

« previous next »
Pages: [1]   Go Down

Author Topic: ford factory mag wheels/rims?! different offsets!!?!!?  (Read 2527 times)

0 Members and 1 Guest are viewing this topic.

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
ford factory mag wheels/rims?! different offsets!!?!!?
« on: March 07, 2012, 04:22:11 AM »
have a set of the alum. mags on my hatchback and have had 2spares for years, well looking on craigslist found 2 more about 1hr and 15min from my house,
well i bought the wheels from the old guy that had them and the offset is different from the ones on my car and the spares i have, did ford make different offsets for the pinto mags? and all the rims i have do have the ford emblem inbossed as well as part numbers, im kinda glad to have an offset but it was a big surprise to me!!
thanks for any input!!
eric
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: ford factory mag wheels/rims?! different offsets!!?!!?
« Reply #1 on: March 07, 2012, 02:53:40 PM »
71/72's and maby 73's have less backspace than 74/80's. Been there/done that.
Logged
Its better to be a has-been, than a never was.

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: ford factory mag wheels/rims?! different offsets!!?!!?
« Reply #2 on: March 07, 2012, 04:42:04 PM »
ok then, well i guess i have a set of two 71-73 for the front and a set of 74-80 for the rear, glad i was not dead set on a matching set of four!!!
 
 
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline Cookieboystoys

  • Eater of Cookies
  • PCCA Management Board
  • Pinto Master
  • ******
  • Posts: 2253
  • FeedBack: +59/-1
  • Gender: Male
  • It's All About The Pinto's! Baby!
    • Cookieboy's Toys on Facebook

    • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Signature Topic Starter Poll Voter Photographer Windows User 1000 Posts Webmaster Fifth year Anniversary
Re: ford factory mag wheels/rims?! different offsets!!?!!?
« Reply #3 on: March 07, 2012, 07:01:01 PM »
Quote from: bbobcat75 on March 07, 2012, 04:42:04 PM
ok then, well i guess i have a set of two 71-73 for the front

if they are the early slots (71-73) they will not work for 74 and up, center hole is to small, try a test fit before you have rubber mounted
Logged
It's all about the Pintos! Baby!

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: ford factory mag wheels/rims?! different offsets!!?!!?
« Reply #4 on: March 08, 2012, 08:53:20 AM »
thats funny how things work out, i was doing the front brakes and the rotors on my 78 are off an 71-73 pinto, so the rims will fit, and here i was so mad about that it worked out to my advantage, well that never happens!!
 
thanks for the input and info guys!!
 
eric
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car
Pages: [1]   Go Up
« previous next »