Current Classifieds

Various Pinto Parts 1971 - 1973

Date: 10/01/2020 02:00 pm
Crane Cam
Date: 02/26/2018 07:50 am
78 pinto wagon

Date: 06/04/2020 12:42 pm
Anyone scrapping a 1980
Date: 03/13/2020 08:46 pm
1975 Pinto bumpers
Date: 01/20/2018 07:51 pm
1977 Pinto Cruizin Wagon

Date: 04/11/2024 04:13 pm
front end parts
Date: 03/30/2018 12:48 pm
Misc pinto parts 71-73 2.0
Date: 05/05/2020 11:56 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
1976 (non hatchback) pinto (90% complete project)

Date: 07/10/2016 10:17 am
Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am

« previous next »
Pages: [1]   Go Down

Author Topic: floors  (Read 1430 times)

0 Members and 1 Guest are viewing this topic.

Offline joe the troll

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
floors
« on: January 19, 2014, 02:15:58 PM »
i know mustang II floors will fit the front with some small modifying but i cant figure out what to use for the rear floors . Or dos anyone know some one that can make a one pice front to rear floor pans? for a 1979 pinto cruiser wagon     thanks
Logged

Offline JohnW

  • Pinto Full Member
  • ***
  • Posts: 229
  • FeedBack: +5/-0
  • Gender: Male
  • 1980 Runabout

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Poll Voter
Re: floors
« Reply #1 on: January 20, 2014, 01:49:58 PM »
I don't think there's anything available. Find a shop that has a bead roller and have them make you some up out of some sheetmetal.
Logged
-

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: floors
« Reply #2 on: January 25, 2014, 08:21:50 PM »
How bad are the floors?  Are they rusted the whole way down?  Typically the area that is raised a bit for the seat doesn't rust out.  I had a 66 Mustang where that middle part was ok but the rest in the front and back were all rusted out.  I made patches and welded them in and it was fine.  That's most likely what you'll have to end up doing because I don't think there is anyone out there making reproduction floor pieces like for other cars like Mustangs, Firebirds and Camaros, etc.  I would use galvanized steel myself.
Logged

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2424
  • FeedBack: +70/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: floors
« Reply #3 on: January 27, 2014, 12:43:01 PM »
On my 78 crusing wagon, I had to replace the pass side floor pan,. front and rear.  I cut some rust free panels from a doner car.  I would maybe try that route before making them.  Someone has to be parting out a car.  I will have to check but I might have one rear section from a 72 parts car I scrapped out a few years back.  I will have to check.
Logged
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)
Pages: [1]   Go Up
« previous next »