Current Classifieds

1978 FORD PINTO PONY FOR SALE 17.000 MILES !!!!!!!!!!!!

Date: 06/25/2021 12:59 am
71 72 front bumper brackets
Date: 06/10/2020 10:55 am
1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
Various parts for 1980 Pony (good to N.O.S. condition
Date: 06/07/2018 01:45 am
1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
6.6.75 carrier
Date: 02/14/2018 06:47 am
WANTED Hood Prop Rod
Date: 01/17/2017 02:47 pm
79 pinto steering column
Date: 08/18/2018 02:00 pm
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
PINTO TRUNK LATCH & CATCH

Date: 03/23/2018 09:39 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am

Author Topic: Epoxy for intake manifold  (Read 1064 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Epoxy for intake manifold
« on: April 17, 2018, 05:54:51 PM »
Hi all.. my custom i take manifold for 2 SU carburetors is almost finished but i need to do some filling around the mating surfaces on the intake ports.  The welds are a bit crude and I have had the mating surfaces surfaced on a head sander but there are some small areas that still need filled. And i also need to smooth and contour the interrior of the manifold ports  match the ports to the ports on the head.

I have read that some folks have used "epoxy" to partially fill the intake ports on a 2.0 and was wondering if any of you have had experience using JB Weld on an intake manifold.

I was contemplating using the "high temp" 500 F degree rated version and was wondering if it would hold up under the heat considering the head shouldnt get above 300 F

Heres a photo of the mating surfaces.

Any suggestions?

Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Epoxy for intake manifold
« Reply #1 on: April 18, 2018, 09:43:49 AM »
A quick Google search (intake ports epoxy) bought this up https://grassrootsmotorsports.com/forum/grm/epoxy-for-intake-port-shaping/32877/page1/

I'd say this is more of a general question for people who do head/intake porting than Pinto people in gerneral. Not say there aren't Pinto people with experience, just saying you are likely to find more info in a borader search. A word that does seem to pop upin this matter is Devcon. Not too sure but it seems an epoxy with aluminum particles inbedded from what I gather is a more stable heat expansion property. Anyway, try the Google - intake ports epoxy - search and you will likely be able to move forward. Do remember though that anything has the potential to dislodge and enter the engine. Hopefully you can find something that significantly minimized that.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Epoxy for intake manifold
« Reply #2 on: April 18, 2018, 11:06:18 AM »
Hi..

Thanks for the info..

I was also.worried about it possibly comming loose so I think ill play it safe and just have more weld built up and then shape it with a rotary file in a drill..
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles