Current Classifieds

1980 Pinto for sale

Date: 11/24/2016 06:32 pm
Need 76' coupe rear Glass and Front Grille
Date: 07/20/2017 01:23 am
Looking for front seats
Date: 08/10/2021 09:54 pm
72 Pinto parts
Date: 12/04/2018 09:56 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
1974 points distributor for 2.3l
Date: 07/04/2022 07:55 pm
Looking for a 1980 windshield
Date: 07/30/2020 04:51 pm
Free ford C3 transmission in 95695..
Date: 06/07/2021 08:14 pm
Pinto drive train

Date: 06/29/2018 08:32 am
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Engine serial # confirmation and carb question  (Read 628 times)

0 Members and 1 Guest are viewing this topic.

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

    • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Engine serial # confirmation and carb question
« on: January 30, 2022, 10:08:01 AM »
My engine serial number is D8EE-06015-BA. 
Am I correct is deciphering this as a 1978 2.3L Pinto (not Escort or truck?)?.
Am trying to find a replacement carb or carb rebuilding kit. 
It's a 1-barrel with 7632S stamped on the base, two other numbers on the carb are 8603 and 8509.
Can't find these numbers cross-referenced anywhere.       
Had a small engine fire this past summer so rebuilding wiring, etc. 
Appreciate any help understanding this info, crossreferenci ng.
Bruce

Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 108
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: Engine serial # confirmation and carb question
« Reply #1 on: January 30, 2022, 11:35:36 AM »
IT COULD BE A 2.0 MOTOR OUT OF A RANGER,THEY HAD 1 BBL CARBS.I CAN LOOK UP YOUR #S TOMORROW.
Logged
D BARHAM

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Engine serial # confirmation and carb question
« Reply #2 on: January 30, 2022, 11:58:27 AM »
If it helps the Escort did not use the Lima 4 cylinder in the Pinto. So, you can rule that out.
Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 108
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: Engine serial # confirmation and carb question
« Reply #3 on: January 31, 2022, 05:28:23 PM »
DEFINETLY A RANGER MOTOR , COULD BE A 2.0 OR 2.3, RANGERS CAME WITH BOTH FROM EARLY 80s AND HAD 1BBL CARBS.
  COULD'NT IDENTIFY BLOCK WITH OUT VIN#
Logged
D BARHAM

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

    • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Re: Engine serial # confirmation and carb question
« Reply #4 on: March 04, 2022, 04:16:26 PM »
Davidpinto and Wittsend,
Thanks for your responses. 
A VIN is not available since the engine is installed in a track roadster.
All four of my intake ports are round but some 2.0 and 2.3 intake gaskets have larger, oval-shaped holes in #1 and 4 ports and won't work.
The rest of the gasket matches up (bolt and port holes) including the water port in the center of the four intake ports.   
Why the difference?  Does that help to identify the engine?   


Logged
Pages: [1]   Go Up
« previous next »