Current Classifieds

pro stock front end
Date: 06/28/2019 07:43 pm
77-78 front grill
Date: 04/07/2017 12:35 am
74 Driver side Wagon Fender, 74 driver side Door, Nice Wheels

Date: 09/15/2019 08:30 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
Need 4 wheel center caps for 77 Pinto Cruzin Wagon
Date: 10/03/2018 02:00 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
73 2.0 Timing Crank Gear & Woodruff key WANTED
Date: 09/01/2017 07:52 am
1978 hatch back

Date: 11/29/2019 03:18 pm
1974 Wiring diagram free
Date: 10/27/2019 06:56 pm
Ignition switch 72 pinto wagon 2.0 4 sp
Date: 12/31/2017 09:03 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am

Author Topic: Engine and transmission mount/bushing  (Read 1891 times)

0 Members and 1 Guest are viewing this topic.

Offline mrmellowgold

  • Pinto Member
  • **
  • Posts: 37
  • FeedBack: +0/-0
  • Gender: Male
  • '73 Pinto Wagon

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Engine and transmission mount/bushing
« on: October 21, 2013, 12:30:02 PM »
Hey there! I was wondering how I would go about putting on new rubber mounts or bushings on my 1973 Pinto wagon. The engine rubber mounts are old and falling apart, and the transmission rubber mount is all old and coming right off with a poke of a stick.
How do I put them on? and where can I find the proper ones? Any website that sells them?

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Engine and transmission mount/bushing
« Reply #1 on: October 21, 2013, 02:01:28 PM »
Hi,


Check Rockauto, they have a lot of parts for good prices.


Dennis

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Engine and transmission mount/bushing
« Reply #2 on: October 21, 2013, 02:01:48 PM »
Local parts stores should have them.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Engine and transmission mount/bushing
« Reply #3 on: October 21, 2013, 04:21:42 PM »
they are also on e-bay, all the time!
1973 pinto runabout

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Engine and transmission mount/bushing
« Reply #4 on: October 21, 2013, 04:28:13 PM »
yes dozens on ebay ... if the mounts are broken you will have a difficult time removing them as they have a nut on top and bottom .. you will have to find a way to keep the mount from spinning as you try to remove the nut .. perhaps the weight of the engine will hold it in place .. you just need to lift the engine a couple of inches after you pull the upper and lower nuts off .. the trans mount is easier .. 

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Re: Engine and transmission mount/bushing
« Reply #5 on: October 21, 2013, 10:05:43 PM »
Rock Auto was the only source of a transmission mount and very reasonable. All the other local parts places had to order them and much pricer. Good Luck

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Engine and transmission mount/bushing
« Reply #7 on: October 30, 2013, 03:01:26 PM »
I got mine from O'Reilly. Cheaper than dirt...less than $15 for all 3. And this is where the fun began, for me. lol

Lot's of prying, cursing, and jacks involved. In hindsight...sa ve yourself some trouble, and shave a 1/4 inch off the top and bottom studs on the engine mounts. Transmission mount...either wait for the right one, or prepare to drill holes, depending on build date. (early 2.0)