Current Classifieds

4-14" Chrome Plated Wheels 4 x 108 + 0mm offset with new tires

Date: 09/12/2018 12:33 pm
Early V8 swap headers, damaged, fixable?
Date: 10/25/2019 03:30 pm
Deluxe Steering Wheel
Date: 10/16/2017 08:13 am
ford pinto door panels
Date: 03/20/2022 07:51 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/12/2018 04:07 pm
looking for parts
Date: 06/19/2020 02:32 pm
2 liter blocks and heads
Date: 03/28/2018 09:58 am
1976 Ford Pinto Wagon - just rebuilt. 302 v8

Date: 11/11/2019 03:38 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
wanted a 1979 Pinto or Bobcat front valance
Date: 03/17/2019 10:15 pm
SVO SWAP
Date: 03/15/2018 03:12 am

Author Topic: Electric choke  (Read 1766 times)

0 Members and 1 Guest are viewing this topic.

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Electric choke
« on: February 21, 2013, 10:46:18 AM »
Where can I connect a holley eletric choke? I need a 12v source with key on? Directions say not to use OEM alternator connection.

Offline richcon76

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • The American Mini

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: Electric choke
« Reply #1 on: February 21, 2013, 11:40:38 AM »
Connect the long wire from the kit to the positive choke cap to the terminal marked (+). Connect the other end of the wire to
an ignition activated 12V source. The choke cap should only get voltage when the engine is running. Check your voltage
source with a voltmeter. The 12V source selected should be fused. If not, an inline fuse rated at 10 amps should be installed.

Check to see if you have 12v at the ignition coil. Some may have lower voltage because of resistores, but I would check. If you have 12v then ad a 10a fuse and you should be good as long as you only have power with the key on. Or you can find a line that goes to the fuse box that is only on with the ignition and running engine.

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Electric choke
« Reply #2 on: February 21, 2013, 04:09:59 PM »
I was thinking fuse box. Directions say not to use coil also.

Offline 289Wagon

  • Pinto Full Member
  • ***
  • Posts: 234
  • FeedBack: +29/-3
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary
Re: Electric choke
« Reply #3 on: February 22, 2013, 04:37:00 AM »
 If you connect it to a 12V keyed source the choke will begin to heat up & start to open as soon as the key is turned 'on'. So if you wait a couple of min. before starting the choke will be open & more or less useless. Also anytime the key is 'on.' while you may be doing other things the choke will heat up.
 I've used the 'S' (stator) terminal in the the past & plan to use it on my current build also. It only has power when the alt is turning. You could add a additional O/P switch but that may require the use of a relay to handle the load of the choke.
Still living the dream...In a points & condenser world.