Current Classifieds

1976 (non hatchback) pinto (90% complete project)

Date: 07/10/2016 10:17 am
Pinto Vinyl Top

Date: 10/09/2020 10:29 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
Pinto Fiber Glass Body Parts
Date: 01/06/2019 06:53 pm
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
78 hatchback

Date: 03/12/2023 06:50 pm
Looking for a 1977 Ford Pinto Runabout Hatchback
Date: 04/27/2018 10:28 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
1973 Interior parts wanted
Date: 01/02/2017 11:02 pm
hubcaps

Date: 10/31/2018 12:04 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
WTB. Seat cover or material LFront
Date: 07/01/2019 03:17 pm

Author Topic: Driveshaft  (Read 2455 times)

0 Members and 1 Guest are viewing this topic.

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Driveshaft
« on: June 02, 2013, 04:49:22 PM »
I just finished installing a 1975-77 MustangII 8" rear in my 1979 Pinto with 302 and C4 trans. My question is will the driveshaft fit from the 6 3/4 rear that I removed. I am getting conflicting info on this.

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Driveshaft
« Reply #1 on: June 02, 2013, 10:10:46 PM »
Did you have a C-4 in the first place ? If not change the slip yoke to one that's for the T-5 and the C-4. Have you a least test fit it first. Is the engine/trans longer than a 2.3 and 4 speed etc.

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Driveshaft
« Reply #2 on: June 03, 2013, 05:00:43 AM »
Yes, the 302 and C4 were in there before the 8" swap. I bought the car with the 302 and C4 with the6 3/4 rear in the car, drove it home as a matter of fact. The guy I purchased the car from gave me the 8" which I rebuilt and installed over the weekend. I have the C4 trans out and rebuilding that. Just trying to find out about the driveshaft from what I am reading some are saying I need a driveshaft from a Pinto manual car. I am trying to clarify this.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Driveshaft
« Reply #3 on: June 03, 2013, 07:18:28 PM »
Ok, not sure if this helps.  I went from a C-4 ('73 behind a 2000) to a T-5 behind a 2.3.  I also swapped out the 6-3/4" to an 8".  The original driveshaft fit perfectly.

  So, assuming the transmission location remained the same in your car, - if the C-4 and the T-5 (from an '88 Turbo Coupe) are the same length (I don't know that they are) then I would say probably yes.

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Driveshaft
« Reply #4 on: June 03, 2013, 08:36:04 PM »
You should be fine. If you had a C-3 or the four speed than you would have to change. The C-4 and the T-5 slip yoke are the same. You might want to throw on a new set of U-joints while the drive shaft is out. The so called lifetime warranty items are not grease able, the two year warranty ones from AutoZone are, I do not know why but they are. The part numbers should be the same as the V-6 by the way.

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Driveshaft
« Reply #5 on: June 04, 2013, 06:54:21 AM »
. The so called lifetime warranty items are not grease able, the two year warranty ones from AutoZone are, I do not know why but they are.
the greaseable ones have holes in them for grease ... making them weaker ...

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Driveshaft
« Reply #6 on: June 04, 2013, 01:11:41 PM »
U-joints are done. Thanks everybody sounds like I should be good on the driveshaft then. I just didn't need anymore delays looking for parts. Thanks again.