Current Classifieds

78-80 Windshield
Date: 10/29/2021 03:11 pm
Intake manifolds

Date: 03/06/2021 03:04 pm
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm
parts needed
Date: 02/20/2017 07:58 am
Looking for a few parts - TIA
Date: 02/19/2023 12:18 pm
2 liter blocks and heads
Date: 03/28/2018 09:58 am
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
74 hood
Date: 07/03/2017 03:46 pm
2.0 Cyl Head1973
Date: 11/29/2018 12:51 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 2.0 camshaft spray bar o ring  (Read 809 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
2.0 camshaft spray bar o ring
« on: November 29, 2018, 03:10:18 PM »
Does anyone have experience with the cam spray bar needing an o ring where it connects to to the center cam support tower to seal.

Was there one installed at the factory and are they necessary

Ive seen install videos where an o ring was used but have found no place where an o ring is sold.

Ive even dug into my box of o rings and cant seem to find one of the correct diameter and thickness that seem to fit.

The fit of the nipple on the spray bar is pretty loose in the hole in the cam tower so it would make sense that a seal of some sort would be necessary to prevent pressure loss here..

As a precaution i sealed the joint with some #2 permatex (non hardening and oil proof).

Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Pintosopher

  • 33yrs SCCA, 19yrs Egroups/PCCA ,40yrs enlightenment
  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2000
  • FeedBack: +383/-1
  • Gender: Male
  • Essses my Nirvana , Liberty to play, my mission

    • Total Badges: 9
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter 1000 Posts Windows User Tenth year Anniversary Fifth year Anniversary Photographer
Re: 2.0 camshaft spray bar o ring
« Reply #1 on: November 30, 2018, 07:23:53 AM »
LTFM,
 Yes, the O ring is necessary. Only in certain Roller Rocker /Needle bearing Cam applications is it an advantage to limit the oil to the followers. (Vizard book) I would check with B.A.T. for the O rings, they were the racers engine parts for EAO 2.0 Formula cars (FF2000 & S2000) years ago, maybe still are.
 Hope this helps.
 Pintosopher :)
Logged
Yes, it is possible to study and become a master of Pintosophy.. Not a religion , nothing less than a life quest for non conformity and rational thought. What Horse did you ride in on?

Check my Pinto Poems out...

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 2.0 camshaft spray bar o ring
« Reply #2 on: December 04, 2018, 09:41:21 PM »
Update...

Well I called Ivy Engineering in Portland and they sId that they used a .200 ID x .070 thick O ring.

With some research, I found a box of metric O rings at harbor freight for $5 that included an assortment of O rings..

The one I selected was 5mm ID and 2 mm thick which fit..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »