Current Classifieds

77 Cruising wagon Rear cargo light
Date: 10/02/2017 02:16 pm
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
1974 Pinto Inside Rear View Mirror & Brake Pedal Pad

Date: 02/18/2017 04:41 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
1971 Pinto Runabout turn key driver

Date: 12/04/2018 07:40 pm
76 drivers fender
Date: 07/20/2018 08:24 pm
1975 Pinto bumpers
Date: 01/20/2018 07:51 pm
77 Cruising Wagon Front Seats
Date: 04/12/2017 12:37 pm
Lower Alternator bracket
Date: 08/26/2017 05:11 pm
Need Interior Panels
Date: 07/09/2018 04:59 pm
 Alloy Harmonic Balancer

Date: 07/10/2020 12:17 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Curb idle  (Read 1654 times)

0 Members and 1 Guest are viewing this topic.

Offline 1974pintowagon!

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Curb idle
« on: July 13, 2017, 11:13:02 PM »
I'm trying to figure out the curb idle for my 2.3 with 4 speed should be set at. I'm also wondering why my pinto would be popping through the exhaust when shifting and on deceleration.
Logged

Offline 1974pintowagon!

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Curb idle
« Reply #1 on: July 15, 2017, 02:17:56 AM »
Anyone??? No one knows the specs on what rpm the idle should be set at? In can't seem to find specs on this anywhere
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Curb idle
« Reply #2 on: July 15, 2017, 06:13:52 PM »

My Clymer's manual says:


 "Curb Idle (solenoid - On) 1973-1974  See emission decal" Well, isn't that a great help.  >:(


 " Idle Speed (solenoid Off) 2.3 (thru 1976) 550 RPM"


My Haynes manual...,though it states "thru 1974" does not even acknowledge that ford used a 2.3 in the Pinto in '74!  >:( >:(


My Pinto came with a 2.0 and a missing Decel valve. I then went immediately to a Turbo motor. So, while lacking that knowledge..., you might want to investigate the Decel valve as a cause because the problem seems to occur when you lift the throttle. It is during those high vacuum times that the valve is active. That said many people seem to remove them because they are a problem.



Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Curb idle
« Reply #3 on: July 16, 2017, 11:08:14 AM »
I've always set the idle as low as the engine would keep running in day to day driving. On Pintos that are hopped up that might be as high as 1000 rpm due to a cam change. Works for me.
Logged
Its better to be a has-been, than a never was.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Curb idle
« Reply #4 on: July 19, 2017, 03:27:25 PM »
Just remember that a 100,000+ mile Pinto is not likely to idle at the same RPM as a new one. Play it by ear and you'll be ok. If the car will move fast from a dead stop without touching the gas pedal your idle is most likely too high.
Logged
Its better to be a has-been, than a never was.
Pages: [1]   Go Up
« previous next »