Current Classifieds

1971 Pinto

Date: 03/04/2017 11:28 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
74 Wagon body parts and a couple of 79 bits

Date: 11/14/2019 04:02 am
Bellhousing for C4 to 2.0 litre pinto
Date: 01/30/2017 01:48 pm
1978 Pinto Wagon V8
Date: 04/28/2023 03:26 pm
convert to stick
Date: 05/19/2018 09:26 pm
1973 Pangra

Date: 01/06/2015 02:19 pm
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am
Cruiser Dash Gauges
Date: 12/04/2016 11:50 am

« previous next »
Pages: [1]   Go Down

Author Topic: Crank pulley and outer timing cover Help  (Read 1188 times)

0 Members and 1 Guest are viewing this topic.

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Crank pulley and outer timing cover Help
« on: April 19, 2023, 01:13:42 PM »
Finally found a junk yard with a couple Pintos. One of which was a 2.3 with the outer timing cover still there. That’s what I needed. Pulled the bolts and….discovered that you need to pull the crank pulley to remove said cover.  70 mile round trip. :-\  So, two questions:

Is it true you need to pull crank pulley to get the outer cover off?

How hard are these pulleys to remove?  Been sitting there for a loooong time. Spray lube, impact, pry bars, three jaw puller?  Any tips or advice appreciated!

Thanks.
Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 108
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: Crank pulley and outer timing cover Help
« Reply #1 on: April 19, 2023, 06:41:57 PM »
I 'VE NEVER HAD TO REMOVE PULLEY TO GET THE COVER OFF.YOU HAVE TO FENAGLE IT A LITTLE TO FIND THE SWEET SPOT AROUND BRACKETS .PULLEY IS NOT PRESSED ON .
Logged
D BARHAM

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 380
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #2 on: April 22, 2023, 07:13:49 PM »
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run. 
Logged
rob289c

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Crank pulley and outer timing cover Help
« Reply #3 on: April 22, 2023, 10:14:46 PM »
Quote from: rob289c on April 22, 2023, 07:13:49 PM
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run.

Think a regular propane torch would work?  Don’t have a Mapp one and I’m not gonna even try to haul the oxy / acetylene rig down there.
Logged

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 380
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #4 on: April 24, 2023, 07:30:50 PM »
I'm not sure if the propane torch would be hot enough.  The pulley has been on the snout for over 40 years so it might take a bit to free it up.  If that's all I had, I would give it a try. 
Logged
rob289c
Pages: [1]   Go Up
« previous next »