Current Classifieds

Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
1978 ford pinto door striker (passenger side)
Date: 09/01/2017 11:58 am
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
Ignition switch 72 pinto wagon 2.0 4 sp
Date: 12/31/2017 09:03 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
wanted a 1979 Pinto or Bobcat front valance
Date: 03/17/2019 10:15 pm
Need seals Pinto Wagon
Date: 02/16/2017 05:09 pm
78-80 Windshield
Date: 10/29/2021 03:11 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
74 pinto
Date: 09/11/2016 06:32 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Crank pulley and outer timing cover Help  (Read 1359 times)

0 Members and 1 Guest are viewing this topic.

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Crank pulley and outer timing cover Help
« on: April 19, 2023, 01:13:42 PM »
Finally found a junk yard with a couple Pintos. One of which was a 2.3 with the outer timing cover still there. That’s what I needed. Pulled the bolts and….discovered that you need to pull the crank pulley to remove said cover.  70 mile round trip. :-\  So, two questions:

Is it true you need to pull crank pulley to get the outer cover off?

How hard are these pulleys to remove?  Been sitting there for a loooong time. Spray lube, impact, pry bars, three jaw puller?  Any tips or advice appreciated!

Thanks.
Logged

Offline davidpinto

  • PCCA Charter Member
  • Pinto Full Member
  • *
  • Posts: 110
  • FeedBack: +19/-0
  • Gender: Male
  • pinto enthusiast

    • Total Badges: 4
    Badges: (View All)
    Photographer Topic Starter Signature Poll Voter
Re: Crank pulley and outer timing cover Help
« Reply #1 on: April 19, 2023, 06:41:57 PM »
I 'VE NEVER HAD TO REMOVE PULLEY TO GET THE COVER OFF.YOU HAVE TO FENAGLE IT A LITTLE TO FIND THE SWEET SPOT AROUND BRACKETS .PULLEY IS NOT PRESSED ON .
Logged
D BARHAM

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 386
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #2 on: April 22, 2023, 07:13:49 PM »
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run. 
Logged
rob289c

Offline Creedmoor

  • Pinto Member
  • **
  • Posts: 13
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Crank pulley and outer timing cover Help
« Reply #3 on: April 22, 2023, 10:14:46 PM »
Quote from: rob289c on April 22, 2023, 07:13:49 PM
If the junkyard allows it, bring a Mapp Gas torch.  You may need heat to get the pulley off.  Mine took a lot of persuasion to get off.  In the end, the heat did the trick.  I don't think you need to take the pulley off but it may make it easier to get the timing cover off in the long run.

Think a regular propane torch would work?  Don’t have a Mapp one and I’m not gonna even try to haul the oxy / acetylene rig down there.
Logged

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 386
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Crank pulley and outer timing cover Help
« Reply #4 on: April 24, 2023, 07:30:50 PM »
I'm not sure if the propane torch would be hot enough.  The pulley has been on the snout for over 40 years so it might take a bit to free it up.  If that's all I had, I would give it a try. 
Logged
rob289c
Pages: [1]   Go Up
« previous next »