Current Classifieds

1980 cruising wagon ralley

Date: 07/12/2019 01:41 pm
Pangra wanted
Date: 02/05/2017 01:58 pm
Clutch/brake pedal assemble
Date: 12/21/2017 11:26 am
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
Radiator
Date: 05/27/2018 06:07 am
parting out 1975 & 80 pintos
Date: 10/31/2018 12:00 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm

Author Topic: Compression Ratio  (Read 1770 times)

0 Members and 1 Guest are viewing this topic.

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Compression Ratio
« on: February 23, 2013, 01:45:11 AM »
I just did a compression test on my stock 1971 2.0. I got: 145, 147, 145, 145 on a warmed up engine. Then I did the wet (oil) test and got:   145, 152, 145, 150  I normally get blue smoke on start up and she will puff out sometimes while idling. Is this compression too low? Could the smoke be from valve guides or the seals? Thanks     

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Compression Ratio
« Reply #1 on: February 23, 2013, 04:20:05 AM »
Valve seals will cause the blue puff. Seals are no good and oil gets by them and leaks into the cylinder, when you start it you get your blue puff.

Offline fast64ranchero

  • Pinto Sr. Member
  • ****
  • Posts: 250
  • FeedBack: +3/-0
  • Gender: Male

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #2 on: February 23, 2013, 12:14:39 PM »
As stated above, it's valve stem seals, The  2.0L has a flooded top end and the valve stem seals are an issue if old or not installed correctly.
You can do them without pulling the head by making a fork tool to compress the valve springs.
71 Pro-Street pinto 2.3T powered
72 Treasure Valley Special 26K miles pinto
72 old V-8 parts Pinto
73 pinto, the nice one...

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #3 on: February 23, 2013, 08:34:02 PM »
Your compression is fine , change your valve seals.......

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #4 on: February 24, 2013, 12:51:52 AM »
Just want to thank you for the inputs. Valve stem seals it will be. Thanks again. :)