Current Classifieds

1978 Squire wagon 6 Cly
Date: 03/08/2021 10:44 am
Wanted Pinto Fiberglass Body Parts
Date: 05/19/2018 04:56 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm
Gazelle Replicar Pinto powered frame

Date: 01/28/2017 12:30 pm
Clutch/brake pedal assemble
Date: 12/21/2017 11:26 am
74 Wagon Interior
Date: 01/22/2017 06:38 pm
Front sump oil pan
Date: 01/02/2017 06:54 pm
Need 76' coupe rear Glass and Front Grille
Date: 07/20/2017 01:23 am
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
V8 rear end
Date: 04/12/2018 10:57 am
72 pinto wagon. 1 owner. 67K miles
Date: 10/14/2019 08:24 pm
1976 Pinto

Date: 10/24/2017 02:00 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Compression Ratio  (Read 1776 times)

0 Members and 1 Guest are viewing this topic.

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Compression Ratio
« on: February 23, 2013, 01:45:11 AM »
I just did a compression test on my stock 1971 2.0. I got: 145, 147, 145, 145 on a warmed up engine. Then I did the wet (oil) test and got:   145, 152, 145, 150  I normally get blue smoke on start up and she will puff out sometimes while idling. Is this compression too low? Could the smoke be from valve guides or the seals? Thanks     
Logged

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Compression Ratio
« Reply #1 on: February 23, 2013, 04:20:05 AM »
Valve seals will cause the blue puff. Seals are no good and oil gets by them and leaks into the cylinder, when you start it you get your blue puff.
Logged

Offline fast64ranchero

  • Pinto Sr. Member
  • ****
  • Posts: 250
  • FeedBack: +3/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #2 on: February 23, 2013, 12:14:39 PM »
As stated above, it's valve stem seals, The  2.0L has a flooded top end and the valve stem seals are an issue if old or not installed correctly.
You can do them without pulling the head by making a fork tool to compress the valve springs.
Logged
71 Pro-Street pinto 2.3T powered
72 Treasure Valley Special 26K miles pinto
72 old V-8 parts Pinto
73 pinto, the nice one...

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #3 on: February 23, 2013, 08:34:02 PM »
Your compression is fine , change your valve seals.......
Logged

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #4 on: February 24, 2013, 12:51:52 AM »
Just want to thank you for the inputs. Valve stem seals it will be. Thanks again. :)
Logged
Pages: [1]   Go Up
« previous next »