Current Classifieds

1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
77 Cruising wagon Rear cargo light
Date: 10/02/2017 02:16 pm
Wheels and Parts

Date: 07/06/2018 04:50 pm
1974 Ford Pinto

Date: 10/16/2017 10:45 am
Wanted 2.3 engine mount brackets and mounts
Date: 02/14/2018 01:34 am
1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
74 hood
Date: 07/03/2017 03:46 pm
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
73 Runabout

Date: 11/20/2017 03:19 pm
1977 Left Side quarter panel
Date: 06/10/2019 04:16 pm

Author Topic: Coils Prings  (Read 574 times)

0 Members and 1 Guest are viewing this topic.

Offline mklarose

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Male
  • Nova Scotia Pinto

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Coils Prings
« on: October 04, 2020, 07:37:06 PM »
Will coil springs from a 74 or later version fit my 71, 2 lt sedan?
If so will the coils need to be cut and how many?
If later versions do not work well, are there any other models that can be made to fit with good ride height and comfort?

Any thoughts?


Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Coils Prings
« Reply #1 on: October 05, 2020, 04:02:29 AM »
The later 74 up springs are too long in length and would need shorting.  If nobody here provides input, trial and error cutting coils off a 74 up spring could be done.  Also suggest contacting RacerWalsh.com as they advertise coil springs for the 71 with various spring rates.
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Coils Prings
« Reply #2 on: October 05, 2020, 11:57:50 AM »
One of the things about cutting springs is that it stiffens the rate. There are spring calculators that might be helpful to determine how much.  As it is '74 and up springs are probably rate higher because of the 2.3 engine. I don't know the cost (probably not cheap) but I believe you can have springs wound to specification.

  Somewhere (I think it was MOOG) has a chart showing all the wire diameters, coil count, coil circle diameter and free length. It might be by that process you can find a spring "close enough" for another application that can be used. Just as an example a lot of Studebaker guys use aftermarket "Cargo Carrier," variable rate, mid-80's GM FWD, REAR springs - on the FRONT of their cars. This was ultimately determined by using a spring chart and doing a comparison.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: Coils Prings
« Reply #3 on: October 06, 2020, 08:37:22 PM »
What's wrong with the springs you have?
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.