Current Classifieds

v8 springs
Date: 05/07/2017 04:46 pm
Pinto drive train

Date: 06/29/2018 08:32 am
Bell housing
Date: 08/23/2017 05:41 am
1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
1978 bobcat 4speed shifter
Date: 11/02/2023 09:51 pm
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
Wanted 71-73 Pinto grill
Date: 03/09/2019 10:45 pm
Weiand Single plane manifold - for 72 Pinto 4 barrel Carb
Date: 04/25/2017 12:17 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Coils Prings  (Read 588 times)

0 Members and 1 Guest are viewing this topic.

Offline mklarose

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Male
  • Nova Scotia Pinto

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Coils Prings
« on: October 04, 2020, 07:37:06 PM »
Will coil springs from a 74 or later version fit my 71, 2 lt sedan?
If so will the coils need to be cut and how many?
If later versions do not work well, are there any other models that can be made to fit with good ride height and comfort?

Any thoughts?

Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Coils Prings
« Reply #1 on: October 05, 2020, 04:02:29 AM »
The later 74 up springs are too long in length and would need shorting.  If nobody here provides input, trial and error cutting coils off a 74 up spring could be done.  Also suggest contacting RacerWalsh.com as they advertise coil springs for the 71 with various spring rates.
Logged
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Coils Prings
« Reply #2 on: October 05, 2020, 11:57:50 AM »
One of the things about cutting springs is that it stiffens the rate. There are spring calculators that might be helpful to determine how much.  As it is '74 and up springs are probably rate higher because of the 2.3 engine. I don't know the cost (probably not cheap) but I believe you can have springs wound to specification.

  Somewhere (I think it was MOOG) has a chart showing all the wire diameters, coil count, coil circle diameter and free length. It might be by that process you can find a spring "close enough" for another application that can be used. Just as an example a lot of Studebaker guys use aftermarket "Cargo Carrier," variable rate, mid-80's GM FWD, REAR springs - on the FRONT of their cars. This was ultimately determined by using a spring chart and doing a comparison.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: Coils Prings
« Reply #3 on: October 06, 2020, 08:37:22 PM »
What's wrong with the springs you have?
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.
Pages: [1]   Go Up
« previous next »