Current Classifieds

1979 Pinto 3-door Runabout *PRICE REDUCED*

Date: 01/21/2023 04:19 pm
77 pinto cruz. wagon
Date: 06/15/2017 09:18 pm
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
A.c. alternator hrackets
Date: 09/03/2017 12:11 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
78-80 Windshield
Date: 10/29/2021 03:11 pm
McLeod Clutch

Date: 04/12/2017 12:08 pm
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
1600 CC WATER PUMP
Date: 06/02/2018 09:13 am
Need Interior Panels
Date: 07/09/2018 04:59 pm
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm

Author Topic: carburetor problems  (Read 861 times)

0 Members and 1 Guest are viewing this topic.

Offline JonzWagon

  • Pinto Member
  • **
  • Posts: 94
  • FeedBack: +3/-0

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
carburetor problems
« on: May 17, 2018, 06:34:52 PM »
Hi. Looked for answers, but no luck. I am having a carb problem and I need to have it rebuilt or replaced. HOWEVER I have not been able to figure out what kind it is or anywhere to get one or even a rebuild kit. I assume it is a Holly of some sort??? The car is a 1980  wagon with automatic trans and California smog stuff attached. Which I was told makes the carb different than others. Is there a way to identify it?  I keep finding numerous holly 2 bbls with many different apps. The car runs and idles ok, but, has no low speed power.  barely gets up my driveway. I was thinking accelerator pump problem, but don't know if it applies to this carb. If I can find a replacement one that would solve many problems.  Any advice or suggestions would be greatly appreciated.  Thanks for reading this.   John

Offline Pintosopher

  • 33yrs SCCA, 19yrs Egroups/PCCA ,40yrs enlightenment
  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2000
  • FeedBack: +383/-1
  • Gender: Male
  • Essses my Nirvana , Liberty to play, my mission

  • Total Badges: 9
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter 1000 Posts Windows User Tenth year Anniversary Fifth year Anniversary Photographer
Re: carburetor problems
« Reply #1 on: May 18, 2018, 10:14:33 AM »
John , this one has too many possibilities, first verify that all of the CA smog equipment is properly hooked up, Then look for a possible EGR issue, ( Stuck open) . If you remove the air cleaner and watch for the accelerator pump jets when you activate the throttle, you may be able to eliminate that possibility. Put a Vacuum gauge to the intake manifold and get a reading at idle, and then watch when the throttle is opened. The gauge should read a steady 11 to 17 inches of vacuum at idle and drop as the throttle is opened. A fluttering  or low reading at idle is the first clue. More after the verification of fuel , pumps squirting , and elimination of vacuum leaks that may be present. There could be stuck temp control TVSS vacuum valves  issues too. More on that later.
 Start with the basics ..
 Pintosopher
Yes, it is possible to study and become a master of Pintosophy.. Not a religion , nothing less than a life quest for non conformity and rational thought. What Horse did you ride in on?

Check my Pinto Poems out...

Offline JonzWagon

  • Pinto Member
  • **
  • Posts: 94
  • FeedBack: +3/-0

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: carburetor problems
« Reply #2 on: May 18, 2018, 10:00:56 PM »
Pintosopher... ..........Many thanks for the advice.  Will go thru your ideas this weekend. I will check the CA smog set up. It has been 4 years since I was in CA. and had to pass a test.  I know where to borrow a Vac Gauge so  thanks again you got me started on what to look for.  John