Current Classifieds

72 pinto

Date: 06/23/2016 12:40 pm
pinto floor mats??

Date: 01/11/2017 07:27 am
Rare parts for sale
Date: 09/10/2018 08:38 am
Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
71-73 sway bar
Date: 06/12/2021 10:12 am
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
74 Pinto Wagon Squire.Bright blue

Date: 06/30/2018 09:48 am
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
Wanted early pinto
Date: 10/03/2019 02:42 pm
WTB: Factory air cleaner and fan shroud 1971 2.0
Date: 02/05/2020 11:06 am
1978 ford pinto carb
Date: 02/04/2018 06:09 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm

Author Topic: Carb?  (Read 1890 times)

0 Members and 1 Guest are viewing this topic.

Offline John Turner

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Fifth year Anniversary Apple User
Carb?
« on: October 24, 2012, 02:49:54 PM »
72 Pinto Wagon , 2000CC, 2V carb.  Restored the car inside and out.  Replaced plugs, points, rotor, distr. cap, wires, fuel pump, hoses, belts, etc.  Runs poorly.  Tried a new (rebuilt carb.) It ran worse, floats in new carb. sticking etc. Sent is back.  Put original carb back on, Idle very rough, starves out and stalls, hesitations when warmed up, flat power. 

1) should I go for another rebuilt carb?
2) where can I find a schematic that shows the location of adjustments on carb., and that tells me what they should be set at?
3) should I just take it to a really good mechanic.?

Thanks, jt

Offline Reddog

  • Pinto Member
  • **
  • Posts: 62
  • FeedBack: +0/-0
  • Gender: Male
  • Pinto lover from way back

  • Total Badges: 1
    Badges: (View All)
    Signature
Carb?
« Reply #1 on: October 24, 2012, 03:52:18 PM »
Sounds like a vacuum leak.
Everyday is a gift! Live it to the fullest with no regrets!

Offline Srt

  • Original Pangra Master Builder
  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1339
  • FeedBack: +100/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Linux User Mobile User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: Carb?
« Reply #2 on: October 24, 2012, 09:48:42 PM »
vacuum connections on those early models are minimal (compared to later models), Check all the vacuum hoses & connections for leaks.  There should be a decal somewhere in the engine compartment or on the engine that will show the routing.
 
make sure the carb mounting nuts are secure. find the 'decel' valve and make sure it is not sucking air.  these can go bad.
 
 
the only substitute for cubic inches is BOOST!!!

Offline Reddog

  • Pinto Member
  • **
  • Posts: 62
  • FeedBack: +0/-0
  • Gender: Male
  • Pinto lover from way back

  • Total Badges: 1
    Badges: (View All)
    Signature
Carb?
« Reply #3 on: October 25, 2012, 07:46:08 AM »
30 years ago I had similar conditions, did the exact things you have done, ended up finding the vacuum leak in the oil separator/PCV hose, it was hard and cracked and didn't seal properly at connections.
Everyday is a gift! Live it to the fullest with no regrets!

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Carb?
« Reply #4 on: October 26, 2012, 08:36:34 AM »
I had issues with the same symptoms. Turned out I was having a MASSIVE vacuum leak due to a ruptured diaphragm in my deceleration valve, so I removed it and plugged its hole with a pipe plug (painted aluminum)(3/8 NPT, iirc) and some teflon tape and haven't looked back. :) Is it Concours worthy? Nope, but it screams and is running about as perfect as it gets. I've replaced just about everything you have...plus had to have my head rebuilt due to destroyed exhaust valves, but that's another story. :)