Current Classifieds

1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
78 pinto wagon

Date: 03/03/2020 01:07 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
99' 2.5l lima cylinder head

Date: 01/13/2017 01:56 am
Wanted Postal Pinto
Date: 09/26/2019 05:31 pm
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
Need flywheel for 73 2.0 engine.
Date: 10/05/2017 02:26 pm
76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
door sills
Date: 03/14/2020 03:20 pm

« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: roller cam?  (Read 23473 times)

0 Members and 1 Guest are viewing this topic.

Offline jonz2pinto

  • Pinto Member
  • **
  • Posts: 83
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Linux User Mobile User
Re: roller cam
« Reply #90 on: May 06, 2014, 07:47:33 PM »
Cam was to replace  2500-7500 power range cam(hyd roller)105mph,2 nd gear(auto)3.08 rear,205 50 15 tires.would not go any faster in drive.also 390 holley 4 on 4bbl offy inake,headers,unported heads(limiting factor i believe).ignition was hipo too. Slower then stock below 15-20mph.have 4.56 and 3.40 8inch stumps that i thought of using for takeoff but would not help top end.was going for street-strip car.
Logged
Pinto-is short for pint-o-fun.

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: roller cam?
« Reply #91 on: May 06, 2014, 08:09:16 PM »
Over the years I've had "STREET" cars with 4.56, 4.86 & 5.38 gears out back when I was street racing. I also ran slicks, soft compound street tires & rim screws on these cars. NONE of this stuff works the minute you jump on the highway & try to drive 65 mph for longer than 30 seconds. Trust me!!
 
Run the 3.40 & swap in the 4.56 for the track only. Rarely are you going to be using the engine below 2000 rpm so the slight loss of bottom end wont come into play.
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: roller cam?
« Reply #92 on: May 06, 2014, 11:16:48 PM »
X2. The words street/strip car and a four cylinder do not belong in the same sentence together unless there is a turbo involved. I view hopping up these as just an exercise in making the car powerful enough to hold its' own on the freeway with the big boys. Why the Contour and Focus zetecs were such a breath of fresh air, cars that could accelerate without dropping them off a cliff. That last 30 hp. is to kill for in street driveability.. ............

I ran an AMC car on the street with 5.0 gear and a 304 that would run in the elevens, it got pretty bad cruising for long distances and the gas price now would simply kill you.
Logged
Pages: 1 2 3 [4]   Go Up
« previous next »