Current Classifieds

1975 Ford Pinto

Date: 01/13/2020 11:02 am
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am
Anyone scrapping a 1980
Date: 03/13/2020 08:46 pm
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
Hatch needed
Date: 09/10/2017 09:16 pm
Wheels and Parts

Date: 07/06/2018 04:50 pm
Wanted Type 9 5spd Transmission
Date: 07/04/2017 03:26 pm
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
Racing seats
Date: 10/24/2019 09:41 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/18/2017 05:55 pm

« previous next »
Pages: [1]   Go Down

Author Topic: shifter knob detachment  (Read 1675 times)

0 Members and 1 Guest are viewing this topic.

Offline redwinggirl

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
shifter knob detachment
« on: November 28, 2012, 05:51:56 PM »

So I'm driving down the road and begin to downshift at a stoplight , pulling from 3rd to 2nd when the ENTIRE SHIFTER COMES OUT OF THE TRANS. Leaving me literally waving a shifter bar around the car. Luckily it was in 2nd so I could ease into a Napa auto repair that was right there. We reattached it temporarily but I need a SADDLE ASSEMBLY for it. Any advice/clues? Thx, Leslie
Logged

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Re: shifter knob detachment
« Reply #1 on: November 28, 2012, 06:10:18 PM »
 Look here about 7 or 8 posts down `four sped shifter`. Mine used to do that too and the first time it happened I nearly panicked I was on an exit ramp and it was a steep one climbing up. I turned the engine off, and was ready  to leave it over on the side until I saw a police car giving me the eye.It wasnt easy getting that car going in 4th gear up that incline :(

 Eventually I got so god at putting it back together, I woulkd just coast over somewhere there was enough light if it was dark, put it together and take off in about a minute or less.

 After I had the transmission replaced later it never came out again,I was thinking it was the nylon nut that screws into the transmission, but I guess it wasnt. It could be the saddle or shift rail bushing was missing, or maybe grease on the nylon nut (or in the transmission housing where it screws in) or else the transmission itself in my case. If you get the saddle then you might want to clean that nylon nut and the threads inside the top of the transmission a little too. And let us al know how it turns out.
Logged

Offline Srt

  • Original Pangra Master Builder
  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1339
  • FeedBack: +100/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Linux User Mobile User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: shifter knob detachment
« Reply #2 on: November 28, 2012, 08:02:07 PM »
once you get the shifter nylon nut threaded in make sure that you push down a couple of the tabs on the lock ring or it WILL back out again
Logged
the only substitute for cubic inches is BOOST!!!

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Re: shifter knob detachment
« Reply #3 on: November 28, 2012, 10:33:40 PM »
 It didnt sop mine :(
Logged

Offline redwinggirl

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: shifter knob detachment
« Reply #4 on: February 26, 2013, 05:02:07 PM »
Hey, friends, I found the bushing piece for the shifter assembly and had it put in.  3 weeks later the shifter is unscrewed again. Per advise I got iy screwed back in and 1-4 gears are great. However, can't get it in reverse at all. I read a great post by Dave1987 about switching shifter to Mustang ii, trouble is I'm concerned about the no reverse thing. What should I be looking at in terms of trouble shooting?  Thanks!
Logged
Pages: [1]   Go Up
« previous next »