Current Classifieds

ENGINE COMPLETE 1971 PINTO
Date: 12/28/2017 03:55 pm
Need hatchback fuel tank sending unit
Date: 08/13/2018 02:46 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/12/2018 04:07 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am
NOS Sedan decklid

Date: 10/23/2019 11:51 am
71-73 Pinto Parts

Date: 06/06/2019 10:47 am
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
Looking for Plastic? sloping headlight buckets for 77/78
Date: 06/19/2018 03:58 pm

Author Topic: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L  (Read 1539 times)

0 Members and 1 Guest are viewing this topic.

Offline crossy

  • Pinto Member
  • **
  • Posts: 79
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary
I know there is a bracket needed to install the clutch cable. I am AGAIN trying to get back to the 5speed into my 73 that has a 2.0. I have the bell done and would like to fab the bracket needed in advance. Length?, hole sizes?  ppic of install?? thanx. Crossy
ehh ehhh ehhh FIRE! FIRE!

Offline turbopinto72

  • Master Mechanic
  • Administrator
  • Pinto Sr. Master
  • ******
  • Posts: 3065
  • FeedBack: +170/-1
  • Gender: Male
  • Your never to old to go fast.
    • Brads Pintos and Pangras

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Photographer Windows User 1000 Posts Webmaster Tenth year Anniversary Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #1 on: March 16, 2012, 12:16:44 PM »
What bracket are you talking about? Nothing is needed at the bellhousing end. The only thing I did was extend the cable housing clamp that is on the fender wall because the cable have to extend a bit firther.
Brad F
1972, 2.5 Turbo Pinto
1972, Pangra
1973, Pangra
1971, 289 Pinto

Offline crossy

  • Pinto Member
  • **
  • Posts: 79
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #2 on: March 16, 2012, 04:16:03 PM »
flat piece of metal that the clutch cable goes through- one hole for mounting bolt and one larger one for cable. saw pics here once. 
ehh ehhh ehhh FIRE! FIRE!

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #3 on: March 17, 2012, 04:51:20 PM »
I do not have the dimensions but here are a couple of links to photos.
http://www.fordpinto.com/index.php/topic,15844.msg103212.html#msg103212
http://www.joe-escobar.com/pinto.html    scroll down to near the bottom
Jerry J - Jupiter, Florida