Current Classifieds

WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
2.3 engine mounts,glove box parts,emblems,hatch,doors,hinges etc
Date: 08/26/2018 06:35 pm
71-71 speedo cable
Date: 07/31/2021 09:04 pm
1972 Runabout (GOING TO SCRAP BY 5/28)

Date: 05/21/2019 11:50 am
Need 4 wheel center caps for 77 Pinto Cruzin Wagon
Date: 10/03/2018 02:00 pm
78 fender and hood
Date: 03/23/2021 01:07 pm
parts needed
Date: 02/20/2017 07:58 am
'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
Wiring diagram Ignition switch 72 2.0 4 speed pinto wagon
Date: 12/31/2017 11:14 pm
C-3 automatic transmission

Date: 08/17/2022 10:18 am
1975 Ford Pinto

Date: 01/13/2020 11:02 am

« previous next »
Pages: [1]   Go Down

Author Topic: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L  (Read 1517 times)

0 Members and 1 Guest are viewing this topic.

Offline crossy

  • Pinto Member
  • **
  • Posts: 79
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary
ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« on: March 16, 2012, 07:56:46 AM »
I know there is a bracket needed to install the clutch cable. I am AGAIN trying to get back to the 5speed into my 73 that has a 2.0. I have the bell done and would like to fab the bracket needed in advance. Length?, hole sizes?  ppic of install?? thanx. Crossy
Logged
ehh ehhh ehhh FIRE! FIRE!

Offline turbopinto72

  • Master Mechanic
  • Administrator
  • Pinto Sr. Master
  • ******
  • Posts: 3065
  • FeedBack: +170/-1
  • Gender: Male
  • Your never to old to go fast.
    • Brads Pintos and Pangras

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Photographer Windows User 1000 Posts Webmaster Tenth year Anniversary Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #1 on: March 16, 2012, 12:16:44 PM »
What bracket are you talking about? Nothing is needed at the bellhousing end. The only thing I did was extend the cable housing clamp that is on the fender wall because the cable have to extend a bit firther.
Logged
Brad F
1972, 2.5 Turbo Pinto
1972, Pangra
1973, Pangra
1971, 289 Pinto

Offline crossy

  • Pinto Member
  • **
  • Posts: 79
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #2 on: March 16, 2012, 04:16:03 PM »
flat piece of metal that the clutch cable goes through- one hole for mounting bolt and one larger one for cable. saw pics here once. 
Logged
ehh ehhh ehhh FIRE! FIRE!

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: ANYONE- have dimensions on cable bracket needed for swap,5spd to 2.0L
« Reply #3 on: March 17, 2012, 04:51:20 PM »
I do not have the dimensions but here are a couple of links to photos.
http://www.fordpinto.com/index.php/topic,15844.msg103212.html#msg103212
http://www.joe-escobar.com/pinto.html    scroll down to near the bottom
Logged
Jerry J - Jupiter, Florida
Pages: [1]   Go Up
« previous next »