Current Classifieds

1971 Pinto Parting out

Date: 07/06/2018 01:11 pm
71/72 Pinto front end bushing kit
Date: 02/05/2017 09:45 am
1979 hatch needed
Date: 05/13/2018 08:52 pm
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
MISC PINTO PARTS

Date: 08/27/2017 10:23 am
Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
v8 springs
Date: 05/07/2017 04:46 pm
v8 springs
Date: 05/07/2017 04:46 pm
Bell housing
Date: 08/23/2017 05:41 am
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
71/72 Pinto front end bushing kit
Date: 02/05/2017 09:45 am

Author Topic: Anybody with a Chilton manual...  (Read 1230 times)

0 Members and 1 Guest are viewing this topic.

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Anybody with a Chilton manual...
« on: February 09, 2014, 01:09:07 PM »
What size drill bit does adjusting the neutral safety switch require?

Thanks in advance.

~jeremysdad

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Anybody with a Chilton manual...
« Reply #1 on: February 09, 2014, 04:13:13 PM »
It's a #43 (.089) drill bit. These are the closest fraction sizes:
too small 5/64 = .0781
too large 3/32 = .0938

Insert .484 depth (I'm sure 1/2" would be close enough)

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Anybody with a Chilton manual...
« Reply #2 on: February 09, 2014, 05:03:04 PM »
Thank you!

I need to order another manual. :)

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Anybody with a Chilton manual...
« Reply #3 on: February 09, 2014, 05:12:42 PM »
A 3D nail is .083"...numbered drill bit set is probably easier to find, either locally or online. :) lol

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Anybody with a Chilton manual...
« Reply #4 on: February 10, 2014, 12:06:18 AM »
Yes, the #43 bit. Used on other cars too sometimes, I look for a hole that looks right to adjust and commonly the #43 fits it. Apparently they used it on more than one car.