Shiny is Good!
Home
Forum
Help
TinyPortal
Search
Classifieds
Downloads
Gallery
Search
Stats
Store
Links
Advertise
Login
Register
PINTO CAR CLUB of AMERICA
»
Forum
»
Welcome to FordPinto.com, The home of the PCCA
»
General Help- Ask the Experts...
(Moderator:
dga57
) »
Topic:
Anybody with a Chilton manual...
20 Guests, 0 Users
Association Sites
PintoStampede.com
Pinto Page
MustangII.org
AMCGremlin.com
AMCPacer.com
Bullet Stop Guns
Site Features
Show Unread Posts
Show New Replies
PCCA Official Links
PCCA Member Map
PCCA Member Galleries
Charter Members, VIPs, Club Management
PCCA Meets-Car Shows
Pinto Production Statistics
Help Center
PCCA
CLASSIFIEDS
YOUR
SOURCE
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Anybody with a Chilton manual... (Read 1004 times)
0 Members and 1 Guest are viewing this topic.
jeremysdad
Pinto Sr. Member
Posts: 405
FeedBack: +83/-6
Gender:
Restoring a Daily Driver
Total Badges: 4
Badges:
(View All)
Anybody with a Chilton manual...
«
on:
February 09, 2014, 01:09:07 PM »
What size drill bit does adjusting the neutral safety switch require?
Thanks in advance.
~jeremysdad
Logged
Wittsend
Pinto Master
Posts: 2287
FeedBack: +241/-0
Total Badges: 8
Badges:
(View All)
Re: Anybody with a Chilton manual...
«
Reply #1 on:
February 09, 2014, 04:13:13 PM »
It's a #43 (.089) drill bit. These are the closest fraction sizes:
too small 5/64 = .0781
too large 3/32 = .0938
Insert .484 depth (I'm sure 1/2" would be close enough)
Logged
jeremysdad
Pinto Sr. Member
Posts: 405
FeedBack: +83/-6
Gender:
Restoring a Daily Driver
Total Badges: 4
Badges:
(View All)
Re: Anybody with a Chilton manual...
«
Reply #2 on:
February 09, 2014, 05:03:04 PM »
Thank you!
I need to order another manual.
Logged
jeremysdad
Pinto Sr. Member
Posts: 405
FeedBack: +83/-6
Gender:
Restoring a Daily Driver
Total Badges: 4
Badges:
(View All)
Re: Anybody with a Chilton manual...
«
Reply #3 on:
February 09, 2014, 05:12:42 PM »
A 3D nail is .083"...numbered drill bit set is probably easier to find, either locally or online.
lol
Logged
amc49
PCCA VIP
Pinto Master
Posts: 1256
FeedBack: +242/-1
Another Pinto Driver
Total Badges: 4
Badges:
(View All)
Re: Anybody with a Chilton manual...
«
Reply #4 on:
February 10, 2014, 12:06:18 AM »
Yes, the #43 bit. Used on other cars too sometimes, I look for a hole that looks right to adjust and commonly the #43 fits it. Apparently they used it on more than one car.
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
PINTO CAR CLUB of AMERICA
»
Forum
»
Welcome to FordPinto.com, The home of the PCCA
»
General Help- Ask the Experts...
(Moderator:
dga57
) »
Topic:
Anybody with a Chilton manual...