Current Classifieds

77 pinto cruz. wagon
Date: 06/15/2017 09:18 pm
Misc. Pinto parts

Date: 11/09/2019 04:25 pm
1971 Pinto

Date: 03/04/2017 11:28 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm
2.0 performance parts, 2 intakes, header, ported head, more
Date: 10/25/2019 04:05 pm
1976-1980 A/C condensor

Date: 09/21/2020 10:43 pm
1977 Cruiser
Date: 06/29/2019 06:28 am
77-78 front grill
Date: 04/07/2017 12:35 am
SEARCHING HOPELESSLY
Date: 02/02/2017 07:21 am
1973 Ford Pinto, Shift linkage for a/t and cross member
Date: 02/25/2017 08:45 pm
1979 pinto
Date: 04/19/2018 02:02 am

« previous next »
Pages: [1]   Go Down

Author Topic: floors  (Read 1425 times)

0 Members and 2 Guests are viewing this topic.

Offline joe the troll

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
floors
« on: January 19, 2014, 02:15:58 PM »
i know mustang II floors will fit the front with some small modifying but i cant figure out what to use for the rear floors . Or dos anyone know some one that can make a one pice front to rear floor pans? for a 1979 pinto cruiser wagon     thanks
Logged

Offline JohnW

  • Pinto Full Member
  • ***
  • Posts: 229
  • FeedBack: +5/-0
  • Gender: Male
  • 1980 Runabout

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Poll Voter
Re: floors
« Reply #1 on: January 20, 2014, 01:49:58 PM »
I don't think there's anything available. Find a shop that has a bead roller and have them make you some up out of some sheetmetal.
Logged
-

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: floors
« Reply #2 on: January 25, 2014, 08:21:50 PM »
How bad are the floors?  Are they rusted the whole way down?  Typically the area that is raised a bit for the seat doesn't rust out.  I had a 66 Mustang where that middle part was ok but the rest in the front and back were all rusted out.  I made patches and welded them in and it was fine.  That's most likely what you'll have to end up doing because I don't think there is anyone out there making reproduction floor pieces like for other cars like Mustangs, Firebirds and Camaros, etc.  I would use galvanized steel myself.
Logged

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2424
  • FeedBack: +70/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: floors
« Reply #3 on: January 27, 2014, 12:43:01 PM »
On my 78 crusing wagon, I had to replace the pass side floor pan,. front and rear.  I cut some rust free panels from a doner car.  I would maybe try that route before making them.  Someone has to be parting out a car.  I will have to check but I might have one rear section from a 72 parts car I scrapped out a few years back.  I will have to check.
Logged
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)
Pages: [1]   Go Up
« previous next »