Current Classifieds

Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
V8 rear end
Date: 04/12/2018 10:57 am
Wanted hood hinges
Date: 02/17/2020 05:30 pm
Intake manifolds

Date: 03/06/2021 03:04 pm
Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
1971 Pinto Runabout turn key driver

Date: 12/04/2018 07:40 pm
windshield
Date: 04/14/2018 08:53 pm
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
1976 Pinto

Date: 10/24/2017 02:00 pm
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 9" in pinto swaps  (Read 2616 times)

0 Members and 1 Guest are viewing this topic.

Offline mightyss1

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +8/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
9" in pinto swaps
« on: October 26, 2014, 05:14:58 AM »
wondering if there are any models of fords that were close to swaping their 9" into pinto w/o shortening the housings???
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: 9" in pinto swaps
« Reply #1 on: October 26, 2014, 03:30:41 PM »
See the link below.  The 57-59 Fords and the some of 65-66 hi-po 289 Mustangs had 9" rears.  I replaced the 8" rear in my 66 Mustang with a 57 Ford 9".  It bolted in the 66 but I may have shortened the drive shaft, don't remember.   The spring perches would need some modification to match the Pinto.  I would be surprised if you can find any of these in the junk yard now.
http://www.mustangsandmore.com/ubb/FordRearDimensions.html
Logged
Jerry J - Jupiter, Florida

Offline mightyss1

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +8/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: 9" in pinto swaps
« Reply #2 on: October 29, 2014, 02:20:44 PM »
well, my car has a 9" now..it looks stock( not narrowed). it does not have aftermarket axles, but has the big ford axle housing flange. but not the 5 1/2 bolt pattern like on the trucks...? curiosity did kill the cat, right.??
Logged

Offline Pintocrazed

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +24/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Windows User Apple User Mobile User
Re: 9" in pinto swaps
« Reply #3 on: October 29, 2014, 02:21:39 PM »
ANY IDEA WHAT IT CAME OUT OF MIGHTY ?
Logged

Offline mightyss1

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +8/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: 9" in pinto swaps
« Reply #4 on: October 30, 2014, 02:28:56 PM »
nope, the guy i bought it from didnt build the car...so, im playing detective. i did just put a cool disc brake kit on it from summit racing. since it had NO rear brakes at all, just backing plates !!!! wow, just discovered my answer possibly. it has the flat band in the middle, and a bottom drain plug......1957 ford..?!?! :o  how many inches is a stock pinto 6 3/4 rear flange to flange..???
Logged

Offline Pintocrazed

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +24/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Windows User Apple User Mobile User
Re: 9" in pinto swaps
« Reply #5 on: October 30, 2014, 02:54:24 PM »
I THINK ITS 57"
Logged

Offline mightyss1

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +8/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: 9" in pinto swaps
« Reply #6 on: October 30, 2014, 03:26:58 PM »
well, that jives then. my 1957 - 9" axle is 57.25 inches, so it was a direct bolt in....thnx pintocrazed...
Logged

Offline 78_starsky

  • Pinto Sr. Member
  • ****
  • Posts: 401
  • FeedBack: +21/-0
  • Forever Learning

    • Total Badges: 4
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary Windows User
Re: 9" in pinto swaps
« Reply #7 on: November 23, 2014, 10:22:39 AM »
Logged
Pages: [1]   Go Up
« previous next »