Current Classifieds

hood for a 79-80
Date: 11/30/2018 10:55 pm
WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
Hatch needed
Date: 09/10/2017 09:16 pm
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
4 speed pinto transmission

Date: 01/24/2021 07:54 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
Leaf Spring Mount Rubber Insulator
Date: 08/05/2018 01:58 pm
73 rear hatchback glass
Date: 07/06/2017 11:33 am
1978 hatch back

Date: 11/29/2019 03:18 pm
Looking for license plate bracket, interior parts 72' Runabout
Date: 04/12/2017 08:15 am
72 pinto drag car

Date: 07/08/2017 08:25 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II  (Read 1565 times)

0 Members and 1 Guest are viewing this topic.

Offline racinmud

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« on: May 24, 2014, 05:08:24 PM »
Shelled the C3 and thought I would put in a 4 speed.  Found a 4 speed from a 74 Mustang 2.3,  finally found a flywheel and clutch.  Went to install today and after bolting it all together the throw out bearing won't engage pressure plate , not even close.  It is the D5 case and fork that came with the trans.     Took it all apart to make sure fork was on pivot ball and it was.  Any ideas?  Please help
Thanks, Leon       
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« Reply #1 on: May 25, 2014, 04:06:29 AM »
Just guessing that the throw out bearing is not reaching the clutch fingers.  From vague memory, the Mustang II 2.3 flywheel was at least a 1/2 " thicker than the Pinto 2.3 flywheel (looked ridiculously heavy).  If you used a Pinto 2.3 flywheel, it may not work without accommodating modifications.  Throw out bearings and pivot balls are available in different lengths.
Logged
Jerry J - Jupiter, Florida

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« Reply #2 on: May 26, 2014, 03:45:58 PM »
Need the difference in flywheel thickness and add that to pivot ball length. Needs to be pretty close to get correct leverage and full travel of throwout. Or a longer /shorter throwoout bearing involved there.
Logged
Pages: [1]   Go Up
« previous next »