Current Classifieds

1977 Pinto Hatchback Parts

Date: 08/29/2020 05:31 pm
72 Runabout for Sale- Washington

Date: 02/28/2024 02:07 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
1977 Pinto Cruizin Wagon

Date: 08/07/2023 02:52 pm
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
TWM Intake
Date: 08/15/2018 08:20 pm
WANTED: Skinny Rear Bumper w/o guards for '71 or '72 Pinto Coupe
Date: 04/24/2018 11:45 am
Pinto Runabout wanted
Date: 06/05/2018 04:42 pm

Author Topic: 74 disk brake parts  (Read 1930 times)

0 Members and 1 Guest are viewing this topic.

Offline jburt

  • Pinto Member
  • **
  • Posts: 34
  • FeedBack: +0/-0
  • Gender: Male
  • First Time Owner

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
74 disk brake parts
« on: July 16, 2014, 09:00:58 PM »
So... I've got this loud clanking in the front end when I go over any slight bump in the road. I did some checking on the front end and it all seemed reasonably tight. Except, I found the calipers pivot on the screw that secures the mounting key. They move up and down quite a bit.
If I put a little pedal pressure on while going down the street, the clanking stops.
Aha says I... to the brakes I go.  :D
First I research what I can buy over the counter. There is a hardware kit available with new keys, spring clips for the inside pads, and it looks like an anti-rattle spring. (see the picture)

Wait, I thought this was going to be one of those light weight spring thingies to stop rattles. But it's a bar. uh oh.

Now, the only pieces to the kit that already existed on my brakes were the keys and bolts.
Aha! again... Gulp   :o  After about an hour and a half of wallowing around under the wagon I think I got the inner pad clip on correctly. But this curved bar has me stumped.

Any help out there as to where this thing goes?

TIA Jerry
I color outside the lines...
74 Squire Wagon - needs a lot of work.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: 74 disk brake parts
« Reply #1 on: July 16, 2014, 09:57:52 PM »
How many clips do you get per side? You don't clip the inner, rather the back ends of both inner and outer pads to shove them forward. That stops rattle by shoving all the slack out in direction of wheel rotation, it then stays there. . And the curved bar goes between caliper and bracket to take up slack, no looseness with it in place.

Offline jburt

  • Pinto Member
  • **
  • Posts: 34
  • FeedBack: +0/-0
  • Gender: Male
  • First Time Owner

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: 74 disk brake parts
« Reply #2 on: July 16, 2014, 10:29:05 PM »
How many clips do you get per side? You don't clip the inner, rather the back ends of both inner and outer pads to shove them forward. That stops rattle by shoving all the slack out in direction of wheel rotation, it then stays there. . And the curved bar goes between caliper and bracket to take up slack, no looseness with it in place.


Thanks for the quick response.
The kit has two each of the keys, clips, and bars.  If there is supposed to be a clip on each pad then there should be 4 clips. Correct? I'm not clear on where the bar goes. Is it on the top/front of the caliper? I have found exploded views of most things on the car but not this. Tis frustrating.
I'll have to take a closer look at it tomorrow.
Jerry
I color outside the lines...
74 Squire Wagon - needs a lot of work.

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: 74 disk brake parts
« Reply #3 on: July 16, 2014, 11:58:42 PM »
The 4 small anti-rattle clips go on the pads. The 2 long ones go between the caliper mount & the piece that locks it in place. I just replaced a broken one of these last month on my wagon. It sounded like my frontend was about to fall off the car with all the noise the caliper made.
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline jburt

  • Pinto Member
  • **
  • Posts: 34
  • FeedBack: +0/-0
  • Gender: Male
  • First Time Owner

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: 74 disk brake parts
« Reply #4 on: July 17, 2014, 08:56:27 AM »
The 4 small anti-rattle clips go on the pads. The 2 long ones go between the caliper mount & the piece that locks it in place. I just replaced a broken one of these last month on my wagon. It sounded like my frontend was about to fall off the car with all the noise the caliper made.

Thanks for the reply. I'm headed over to work on it now so I'll see if I can figure it out.
I color outside the lines...
74 Squire Wagon - needs a lot of work.

Offline jburt

  • Pinto Member
  • **
  • Posts: 34
  • FeedBack: +0/-0
  • Gender: Male
  • First Time Owner

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: 74 disk brake parts
« Reply #5 on: July 17, 2014, 03:46:01 PM »
Success! It's really simple when you know where things go.
Thanks for the help.
One of these days I'll know enough about these cars to help someone.
Now, on to the next tasks. The under dash is a mess and I need to figure out what's what under there.
I color outside the lines...
74 Squire Wagon - needs a lot of work.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: 74 disk brake parts
« Reply #6 on: July 17, 2014, 08:53:29 PM »
Oooooooooooooh hh, scary, that.......... ..my '80 was a mess with multiple electrical issues but by looking for the fused mass of plastic and redoing everything that went into it, things became 100% functional again.