Current Classifieds

Bumpers
Date: 07/06/2018 04:47 pm
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
Looking for a 1977 Ford Pinto Runabout Hatchback
Date: 10/15/2017 10:03 am
convert to stick
Date: 05/19/2018 09:26 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am
Pinto Wheel Well Trim
Date: 03/29/2017 11:35 am
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
1975 Pinto bumpers
Date: 10/24/2019 01:43 pm
1974 points distributor for 2.3l
Date: 07/04/2022 07:55 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 72 Pinto diff  (Read 1211 times)

0 Members and 1 Guest are viewing this topic.

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
72 Pinto diff
« on: January 27, 2023, 10:18:25 AM »
Never had one apart. I have to put seals in this summer.
Do I have to pull axle bearings ? If so , I'll need to find a new set of bearings....
Advice ?
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 72 Pinto diff
« Reply #1 on: January 28, 2023, 10:03:20 AM »
Bearings are pressed on with a hydrolic press..i chaned my rear.end.awhil e back and the 71-73 rear ends had smaller bearings than the later ones..

74 and up use the larger bearings like the mii s

Why not just upgrade to a mii 8 inch while you are doing it
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: 72 Pinto diff
« Reply #2 on: January 29, 2023, 08:53:35 AM »
Quote from: LongTimeFordMan on January 28, 2023, 10:03:20 AM
Bearings are pressed on with a hydrolic press..i chaned my rear.end.awhil e back and the 71-73 rear ends had smaller bearings than the later ones..

74 and up use the larger bearings like the mii s

Why not just upgrade to a mii 8 inch while you are doing it

Used the 72 diff to make a trailer for a welder....



Logged
Pages: [1]   Go Up
« previous next »