Current Classifieds

A.c. alternator hrackets
Date: 09/03/2017 12:11 pm
Wanted 1973 Ford right fender
Date: 06/03/2017 08:50 pm
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
Anyone scrapping a 1980
Date: 03/13/2020 08:46 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
Bell housing
Date: 08/23/2017 05:41 am
Bellhousing for C4 to 2.0 litre pinto
Date: 01/30/2017 01:48 pm
1978 Squire wagon 6 Cly
Date: 02/16/2020 05:42 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
Seeking parts
Date: 10/18/2020 10:35 am

« previous next »
Pages: [1]   Go Down

Author Topic: 72 Oil pan gasket  (Read 638 times)

0 Members and 1 Guest are viewing this topic.

Offline KoReynolds

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • 72 Pinto Guy

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
72 Oil pan gasket
« on: March 25, 2020, 05:09:22 PM »
I need to replace my oil pan gasket on my 72 pinto, question is do I need to pull the engine or at least raise it up to clear the crossmember or is there enough clearance to get it out?
Logged

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 72 Oil pan gasket
« Reply #1 on: March 25, 2020, 05:24:17 PM »
at most if i remember correctly you just need to lower the rack and pinion and perhaps raise the engine a bit .. it`s been forever since i had a 4 banger in a pinto ..  dont undo the steering at the column knuckle .. just unbolt it from the cross member and let it drop a bit ..
Logged

Offline JoeBob

  • Pinto Sr. Member
  • ****
  • Posts: 536
  • FeedBack: +51/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Photographer Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: 72 Oil pan gasket
« Reply #2 on: March 25, 2020, 10:33:30 PM »
I changed my gasket on my 72   2.0 in 1973. I did nothing but remove the bolts. I know this for sure as I was just 19.  I was lucky if I knew which way a wrench turned in those days. 47 years later, I still not sure. Remind me, is it lefty loosey?
Logged
77 yellow Bobcat hatchback
Deuteronomy 7:9

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 72 Oil pan gasket
« Reply #3 on: March 26, 2020, 09:24:12 AM »
HA !!   it was about 1975 when i did one .. everything since has had some sort of V8 in it ..
Logged

Offline KoReynolds

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • 72 Pinto Guy

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: 72 Oil pan gasket
« Reply #4 on: March 26, 2020, 01:49:43 PM »
I guess I could try it then if needed lower the rack and pinion, thank you again for the help/advice, so glad I found this club!!
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: 72 Oil pan gasket
« Reply #5 on: March 26, 2020, 03:07:35 PM »
This is where these front sump designs pay off. A lot of times a rear sump pan would hit the lower end of the bell housing. That said it can still be a pain to get old gaskets off cleanly and finagle the new gasket around the oil pick up. What works for me is to tie thread through a few of the bolt holes and gasket holes. That way when things get manipulated to get everything in place the gasket isn't falling off. Then, when a few of the bolts get installed you just cut the tread and pull it out.

I'm assuming the gasket is cork. The later 2.3's used a silicone gasket. Even though mine was 25 years old I reused it and never had a leak. Nearly 15 years ago that gasket was about $25. It is likely more now.
Logged

Offline 71pintoracer

  • Pinto Master
  • *****
  • Posts: 1336
  • FeedBack: +37/-0
  • Gender: Male
  • '71 Pinto 5.0 T-5 = lotsa fun!

    • Total Badges: 8
    Badges: (View All)
    Mobile User Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Fifth year Anniversary Photographer
Re: 72 Oil pan gasket
« Reply #6 on: March 27, 2020, 09:35:05 AM »
The thread trick works well. Should be a cork gasket, l think l still have about 10 lol. What l used to do is spray the pan and the pan side of the gasket with spray adhesive and let it dry a few minutes (lay it out first so you have it correct). When you set it on the pan it's not going anywhere!
Logged
If you don't have time to do it right, when will you have time to do it over?

Offline KoReynolds

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • 72 Pinto Guy

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: 72 Oil pan gasket
« Reply #7 on: March 27, 2020, 08:01:27 PM »
Thanks for the tips, never heard that one but makes sense, the gasket is cork, going to try and get done this weekend depending on weather
Logged

Offline KoReynolds

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • 72 Pinto Guy

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: 72 Oil pan gasket
« Reply #8 on: April 01, 2020, 05:58:13 PM »
So...more than I can do right now, rack and pinion does need to be dropped and starter needs to come out as it is right up against the oil pan.  Going to save it for a winter project when I can keep it up on jack stands for awhile. Want to take transmission out and run new lines (leaking) and put new seals in it so at that point would be a good time to do the oil pan also.
Logged
Pages: [1]   Go Up
« previous next »