Current Classifieds

Hatch needed
Date: 09/10/2017 09:16 pm
Pinto Wagon
Date: 05/25/2018 01:50 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
Many Parts Listed Below
Date: 04/20/2018 11:15 am
Pinto brake booster needed
Date: 05/08/2021 09:00 am
Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
Pinto Fiber Glass Body Parts
Date: 01/06/2019 06:53 pm
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
2.3 pinto carb
Date: 08/18/2018 02:07 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 5 lug conversion ?  (Read 2326 times)

0 Members and 1 Guest are viewing this topic.

Offline moneypit

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • MY MONEY PIT

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Windows User Fifth year Anniversary
5 lug conversion ?
« on: April 08, 2013, 06:14:54 PM »
I have two 79 pinto's and would like to convert to 5 lug but dont know if there is a direct fit conversion from another ford of the same era?  Can anyone help?
Logged

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #1 on: April 08, 2013, 07:08:08 PM »
i know that there are a few topics on this. but what i did was, found a v6 car (pinto) with a 8" rear and got some aftermarket axles (mustang ll) with a 5-lug pattern and the 28 spline shafts. or you could have the axles you have now welded and redrilled. as for the front, i got a pair of 9" ( again mustang ll) rotors also with the 5-lug pattern and they just bolted right on. both (front & rear) of my lug patterns are 5x4 1/2". i now run cragar s/s wheels. 15" on rear & 14" on front. and i have had no issues doing this.

hope this helps.  and good luck!
Logged
1973 pinto runabout

Offline moneypit

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • MY MONEY PIT

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #2 on: April 08, 2013, 11:58:27 PM »
Thanks;
What years of mustang II are there 5 lug! The only ones I have seen are 4 lug.
Logged

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #3 on: April 09, 2013, 06:02:45 PM »
they will be from '74 on up. i got my rotors from j.p.l. streetrods here in Pa.. they have a e-bay store. they may be under mustang ll / pinto. if i remember, they came with rotors, wheel bearings and dust caps (which did not fit). i used my old ones.
Logged
1973 pinto runabout

Offline OhSix9

  • Pinto Full Member
  • ***
  • Posts: 248
  • FeedBack: +7/-1
  • Gender: Male
  • Positrac Intercooler Nitrous Turbo Overdrive

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #4 on: April 10, 2013, 09:55:02 AM »
to go 5 lug on the front and upgrade the brakes in the process get granada rotors pinto bearings and seals, you will need a set of aftermarket adapters (40 bucks ebay)  some blazer 4x4 soft lines and some gm metric calipers. this will give you 11 inch 5 lug on the front

now for the rear your easiest option is a diff swap and the overall width will depend on wheel size and offset. to fit 98 cobra 17x8's it took the entire width of an explorer diff to provide the clearance. If you can find a fox body 8.8 from an 87-94 mustang and add a pair off drivers side axles  and brake plates and drums from a ranger/broncoII/ aerostar with either the 7.5 or 8.8 which can swap into the fox housing and make it 5 bolt and be notably closer to stock width, add some spring perches and you are off to the races other good swaps are 65 mustang diff or a granada one but they are getting much rarer , the 8.8 is plentyful and cheap
Logged
Modest beginnings start with the single blow of a horn man..    Now when you get through with this thing every dickhead in the world is gonna wanna own it.   Do you know anything at all about the internal combustion engine?

Virgil to Sid
Pages: [1]   Go Up
« previous next »