Current Classifieds

1972 Pinto for sale

Date: 05/19/2021 12:41 am
78 hatchback

Date: 03/12/2023 06:50 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
Pinto Watch

Date: 06/22/2019 07:12 pm
1979 pinto
Date: 04/19/2018 02:02 am
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/12/2018 04:07 pm
pinto parts for sale
Date: 07/25/2018 04:51 pm
71-73 Rear valance panel
Date: 01/14/2021 06:54 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
Clutch Fork
Date: 03/31/2018 09:12 pm
looking for parts
Date: 06/19/2020 02:32 pm

Author Topic: 5 lug conversion ?  (Read 2317 times)

0 Members and 1 Guest are viewing this topic.

Offline moneypit

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • MY MONEY PIT

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Windows User Fifth year Anniversary
5 lug conversion ?
« on: April 08, 2013, 06:14:54 PM »
I have two 79 pinto's and would like to convert to 5 lug but dont know if there is a direct fit conversion from another ford of the same era?  Can anyone help?

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #1 on: April 08, 2013, 07:08:08 PM »
i know that there are a few topics on this. but what i did was, found a v6 car (pinto) with a 8" rear and got some aftermarket axles (mustang ll) with a 5-lug pattern and the 28 spline shafts. or you could have the axles you have now welded and redrilled. as for the front, i got a pair of 9" ( again mustang ll) rotors also with the 5-lug pattern and they just bolted right on. both (front & rear) of my lug patterns are 5x4 1/2". i now run cragar s/s wheels. 15" on rear & 14" on front. and i have had no issues doing this.

hope this helps.  and good luck!
1973 pinto runabout

Offline moneypit

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • MY MONEY PIT

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #2 on: April 08, 2013, 11:58:27 PM »
Thanks;
What years of mustang II are there 5 lug! The only ones I have seen are 4 lug.

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #3 on: April 09, 2013, 06:02:45 PM »
they will be from '74 on up. i got my rotors from j.p.l. streetrods here in Pa.. they have a e-bay store. they may be under mustang ll / pinto. if i remember, they came with rotors, wheel bearings and dust caps (which did not fit). i used my old ones.
1973 pinto runabout

Offline OhSix9

  • Pinto Full Member
  • ***
  • Posts: 248
  • FeedBack: +7/-1
  • Gender: Male
  • Positrac Intercooler Nitrous Turbo Overdrive

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 5 lug conversion ?
« Reply #4 on: April 10, 2013, 09:55:02 AM »
to go 5 lug on the front and upgrade the brakes in the process get granada rotors pinto bearings and seals, you will need a set of aftermarket adapters (40 bucks ebay)  some blazer 4x4 soft lines and some gm metric calipers. this will give you 11 inch 5 lug on the front

now for the rear your easiest option is a diff swap and the overall width will depend on wheel size and offset. to fit 98 cobra 17x8's it took the entire width of an explorer diff to provide the clearance. If you can find a fox body 8.8 from an 87-94 mustang and add a pair off drivers side axles  and brake plates and drums from a ranger/broncoII/ aerostar with either the 7.5 or 8.8 which can swap into the fox housing and make it 5 bolt and be notably closer to stock width, add some spring perches and you are off to the races other good swaps are 65 mustang diff or a granada one but they are getting much rarer , the 8.8 is plentyful and cheap
Modest beginnings start with the single blow of a horn man..    Now when you get through with this thing every dickhead in the world is gonna wanna own it.   Do you know anything at all about the internal combustion engine?

Virgil to Sid