Current Classifieds

72 Pinto parts
Date: 12/04/2018 09:56 pm
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
1975 mercury bobcat

Date: 08/14/2018 03:40 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
Oil pan front sump style
Date: 01/10/2017 09:19 am
New cam

Date: 01/23/2017 05:11 pm
Front sump oil pan
Date: 01/02/2017 06:54 pm
WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
Radiator
Date: 05/27/2018 06:07 am

« previous next »
Pages: [1]   Go Down

Author Topic: Compression Ratio  (Read 1769 times)

0 Members and 1 Guest are viewing this topic.

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Compression Ratio
« on: February 23, 2013, 01:45:11 AM »
I just did a compression test on my stock 1971 2.0. I got: 145, 147, 145, 145 on a warmed up engine. Then I did the wet (oil) test and got:   145, 152, 145, 150  I normally get blue smoke on start up and she will puff out sometimes while idling. Is this compression too low? Could the smoke be from valve guides or the seals? Thanks     
Logged

Offline wbacon8780

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • Got to go FASTER

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User
Re: Compression Ratio
« Reply #1 on: February 23, 2013, 04:20:05 AM »
Valve seals will cause the blue puff. Seals are no good and oil gets by them and leaks into the cylinder, when you start it you get your blue puff.
Logged

Offline fast64ranchero

  • Pinto Sr. Member
  • ****
  • Posts: 250
  • FeedBack: +3/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #2 on: February 23, 2013, 12:14:39 PM »
As stated above, it's valve stem seals, The  2.0L has a flooded top end and the valve stem seals are an issue if old or not installed correctly.
You can do them without pulling the head by making a fork tool to compress the valve springs.
Logged
71 Pro-Street pinto 2.3T powered
72 Treasure Valley Special 26K miles pinto
72 old V-8 parts Pinto
73 pinto, the nice one...

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #3 on: February 23, 2013, 08:34:02 PM »
Your compression is fine , change your valve seals.......
Logged

Offline tbucketjack

  • Pinto Full Member
  • ***
  • Posts: 107
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User Fifth year Anniversary
Re: Compression Ratio
« Reply #4 on: February 24, 2013, 12:51:52 AM »
Just want to thank you for the inputs. Valve stem seals it will be. Thanks again. :)
Logged
Pages: [1]   Go Up
« previous next »