Current Classifieds

1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
Bumpers
Date: 07/06/2018 04:47 pm
hubcaps

Date: 05/13/2021 05:33 pm
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
Wanted hood hinges
Date: 02/17/2020 05:30 pm
Pinto Engines and engine parts
Date: 01/24/2017 12:36 pm
2.3 pinto carb
Date: 08/18/2018 02:07 pm
Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am
2 liter blocks and heads
Date: 03/28/2018 09:58 am
2 liter blocks and heads
Date: 03/28/2018 09:58 am

Author Topic: 2.3 intake gasket warning and questions  (Read 2096 times)

0 Members and 1 Guest are viewing this topic.

Offline Jerry merrill

  • Pinto Member
  • **
  • Posts: 60
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
2.3 intake gasket warning and questions
« on: October 11, 2013, 10:29:05 PM »
Just thought I would remind you all who have 2.3 engines, I just pulled my head and intake off to fix valve guide seals and I discovered that the last owner of this engine put a D-port gasket on an oval port head sometime in its past, no wonder it never seemed to run like I thought it should. I ended up buying a D-port head because the price was right and it is rebuilt but it has been milled up near to the intake bolt holes. Any idea of about the compression ratio it will have, its a 85 heart shaped head. I could not find a D-port stock carb intake so I ported out the intake ports to the oval port size. It came out nice. I think this head was intended for a pony stock car.

Offline rramjet

  • Pinto Full Member
  • ***
  • Posts: 120
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: 2.3 intake gasket warning and questions
« Reply #1 on: October 11, 2013, 10:58:28 PM »
The guy who just reworked my 2.0 head used to race 2.3's and said they would take 0.1 off the head. Just barely leaving threads for the intake and exhaust bolts. Not sure what kind of compression this resulted in but they start at 8.2:1 so anything helps.

Offline Jerry merrill

  • Pinto Member
  • **
  • Posts: 60
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 2.3 intake gasket warning and questions
« Reply #2 on: October 11, 2013, 11:36:10 PM »
Thanks for the info, that is just like my head is milled.

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: 2.3 intake gasket warning and questions
« Reply #3 on: October 12, 2013, 06:16:39 AM »
To determine the static compression ratio, the volumes need to be measured. This excerpt from the link below may give hint:
The 2300 head can be milled up to the intake bolt holes (approximately .130”). 
Using a flattop piston, generally, .040” off of the head equals about 1 compression point increase for the engine. The heart shaped  combustion chamber cylinder head gives a slightly higher compression ratio.

 
http://static---racerwalsh.app-hosted.com/media/merchant/racerwalsh/Back_2_Basics_Sheet.doc
Jerry J - Jupiter, Florida

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: 2.3 intake gasket warning and questions
« Reply #4 on: October 12, 2013, 07:38:59 AM »
Ok dumb question, why would you pull the head just to change valve seals??..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: 2.3 intake gasket warning and questions
« Reply #5 on: October 12, 2013, 08:47:47 AM »
Ok dumb question, why would you pull the head just to change valve seals??..

If it's mine & has been together over 30 years I'd pull it to change gaskets as well as seals & toss a belt on it too
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: 2.3 intake gasket warning and questions
« Reply #6 on: October 12, 2013, 09:00:33 AM »

If it's mine & has been together over 30 years I'd pull it to change gaskets as well as seals & toss a belt on it too
Well, in that case if it was 30 years old and never torn down I think I'd go down to bare block, lol. Just wondered because I've changed valve seals a ton of times without pulling heads.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline Jerry merrill

  • Pinto Member
  • **
  • Posts: 60
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 2.3 intake gasket warning and questions
« Reply #7 on: October 12, 2013, 10:54:21 AM »
Thanks for the info! Does anyone know who makes the thickest head gasket?

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: 2.3 intake gasket warning and questions
« Reply #8 on: October 12, 2013, 11:02:43 AM »
Check with Fel-Pro they should have what you need I would think.
Art
65 Falcon 2DR 200 IL6 with C4.