Current Classifieds

71 72 front bumper brackets
Date: 06/10/2020 10:55 am
I need a 1976 hood
Date: 12/19/2016 06:02 pm
pinto parts for sale
Date: 07/25/2018 04:51 pm
hubcaps

Date: 10/31/2018 12:04 pm
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
Leaf Spring Mount Rubber Insulator
Date: 08/05/2018 01:58 pm
1976 (non hatchback) pinto (90% complete project)

Date: 07/10/2016 10:17 am
Pinto Parts for sale
Date: 06/19/2017 02:01 pm
1976 Ford Pinto Pony
Date: 09/06/2018 05:40 pm
Pinto Wagon
Date: 05/25/2018 01:50 pm
1980 Ford AM radio
Date: 12/22/2019 11:57 am
1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am

« previous next »
Pages: [1]   Go Down

Author Topic: 2.0 camshaft spray bar o ring  (Read 787 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
2.0 camshaft spray bar o ring
« on: November 29, 2018, 03:10:18 PM »
Does anyone have experience with the cam spray bar needing an o ring where it connects to to the center cam support tower to seal.

Was there one installed at the factory and are they necessary

Ive seen install videos where an o ring was used but have found no place where an o ring is sold.

Ive even dug into my box of o rings and cant seem to find one of the correct diameter and thickness that seem to fit.

The fit of the nipple on the spray bar is pretty loose in the hole in the cam tower so it would make sense that a seal of some sort would be necessary to prevent pressure loss here..

As a precaution i sealed the joint with some #2 permatex (non hardening and oil proof).

Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Pintosopher

  • 33yrs SCCA, 19yrs Egroups/PCCA ,40yrs enlightenment
  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2000
  • FeedBack: +383/-1
  • Gender: Male
  • Essses my Nirvana , Liberty to play, my mission

    • Total Badges: 9
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter 1000 Posts Windows User Tenth year Anniversary Fifth year Anniversary Photographer
Re: 2.0 camshaft spray bar o ring
« Reply #1 on: November 30, 2018, 07:23:53 AM »
LTFM,
 Yes, the O ring is necessary. Only in certain Roller Rocker /Needle bearing Cam applications is it an advantage to limit the oil to the followers. (Vizard book) I would check with B.A.T. for the O rings, they were the racers engine parts for EAO 2.0 Formula cars (FF2000 & S2000) years ago, maybe still are.
 Hope this helps.
 Pintosopher :)
Logged
Yes, it is possible to study and become a master of Pintosophy.. Not a religion , nothing less than a life quest for non conformity and rational thought. What Horse did you ride in on?

Check my Pinto Poems out...

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 2.0 camshaft spray bar o ring
« Reply #2 on: December 04, 2018, 09:41:21 PM »
Update...

Well I called Ivy Engineering in Portland and they sId that they used a .200 ID x .070 thick O ring.

With some research, I found a box of metric O rings at harbor freight for $5 that included an assortment of O rings..

The one I selected was 5mm ID and 2 mm thick which fit..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »