Current Classifieds

72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
71 72 front bumper brackets
Date: 06/10/2020 10:55 am
4 speed pinto transmission

Date: 01/24/2021 07:54 pm
74 Wagon Interior
Date: 01/22/2017 06:38 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
Looking for oil dipstick and tube 2.3L
Date: 11/23/2017 05:44 pm
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm
Radiator
Date: 05/27/2018 06:07 am
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
1978 Squire wagon 6 Cly
Date: 02/16/2020 05:42 pm
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm

Author Topic: 2.0 camshaft spray bar o ring  (Read 773 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
2.0 camshaft spray bar o ring
« on: November 29, 2018, 03:10:18 PM »
Does anyone have experience with the cam spray bar needing an o ring where it connects to to the center cam support tower to seal.

Was there one installed at the factory and are they necessary

Ive seen install videos where an o ring was used but have found no place where an o ring is sold.

Ive even dug into my box of o rings and cant seem to find one of the correct diameter and thickness that seem to fit.

The fit of the nipple on the spray bar is pretty loose in the hole in the cam tower so it would make sense that a seal of some sort would be necessary to prevent pressure loss here..

As a precaution i sealed the joint with some #2 permatex (non hardening and oil proof).

Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Pintosopher

  • 33yrs SCCA, 19yrs Egroups/PCCA ,40yrs enlightenment
  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2000
  • FeedBack: +383/-1
  • Gender: Male
  • Essses my Nirvana , Liberty to play, my mission

  • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Poll Voter 1000 Posts Windows User Tenth year Anniversary Fifth year Anniversary Photographer
Re: 2.0 camshaft spray bar o ring
« Reply #1 on: November 30, 2018, 07:23:53 AM »
LTFM,
 Yes, the O ring is necessary. Only in certain Roller Rocker /Needle bearing Cam applications is it an advantage to limit the oil to the followers. (Vizard book) I would check with B.A.T. for the O rings, they were the racers engine parts for EAO 2.0 Formula cars (FF2000 & S2000) years ago, maybe still are.
 Hope this helps.
 Pintosopher :)
Yes, it is possible to study and become a master of Pintosophy.. Not a religion , nothing less than a life quest for non conformity and rational thought. What Horse did you ride in on?

Check my Pinto Poems out...

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 2.0 camshaft spray bar o ring
« Reply #2 on: December 04, 2018, 09:41:21 PM »
Update...

Well I called Ivy Engineering in Portland and they sId that they used a .200 ID x .070 thick O ring.

With some research, I found a box of metric O rings at harbor freight for $5 that included an assortment of O rings..

The one I selected was 5mm ID and 2 mm thick which fit..
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles