Current Classifieds

Bell housing
Date: 08/23/2017 05:41 am
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
Bumper Guards
Date: 03/28/2017 09:27 pm
Many Parts Listed Below
Date: 04/20/2018 11:15 am
72 pinto wagon. 1 owner. 67K miles
Date: 10/14/2019 08:24 pm
Pinto brake booster needed
Date: 05/08/2021 09:00 am
looking for 1978 pinto head rebuild kit
Date: 05/24/2020 08:19 am
1980 Pinto Parts

Date: 08/05/2020 04:20 pm

Author Topic: 2" Drop Spindles and 13x5.5" Cragars  (Read 1667 times)

0 Members and 1 Guest are viewing this topic.

Offline morpheus256

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary
2" Drop Spindles and 13x5.5" Cragars
« on: May 22, 2012, 03:46:49 PM »
Hi!

I'm in the process of rebuilding the front suspension on the wife's 79. I've ordered in a polygraphite kit from PST, and a replacement set of stock springs from the. I was wondering if I would be able to run a set of 2" drop spindles with the 13x5.5 Cragar SS's up front.

I'm also trying to track down a set of Sway bar brackets for the frame rails, Hers never came with a front sway bar.

Thanks!
Dave
Bone stock 79 Runabout

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: 2" Drop Spindles and 13x5.5" Cragars
« Reply #1 on: May 22, 2012, 04:32:11 PM »
yes you can run those wheels with the drop spindles, i did!
1973 pinto runabout

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: 2" Drop Spindles and 13x5.5" Cragars
« Reply #2 on: May 22, 2012, 05:35:46 PM »
If you ever have a flat, the lower ball joint will be on the ground.
Its better to be a has-been, than a never was.

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: 2" Drop Spindles and 13x5.5" Cragars
« Reply #3 on: May 22, 2012, 06:25:56 PM »
If you ever have a flat, the lower ball joint will be on the ground.

That's an ugly thought.... I hope the 14 x 6 wheels I plan to run will avoid that with my drop spindles.
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline 82expghost

  • Pinto Full Member
  • ***
  • Posts: 154
  • FeedBack: +84/-0
  • Die tires die!

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Mobile User Windows User
Re: 2" Drop Spindles and 13x5.5" Cragars
« Reply #4 on: May 22, 2012, 09:20:22 PM »
it just depends on your offset, to run mustang 15s i had to use 1 inch of spacer, and while your front end is apart, get arp wheel studs, if you have new ballmounts depending on brand, they might rub at full lock. if you get the heidts bottom arms you wont have this problem.
98 taurtus, now in heaven
82 exp, the race car, cancer took it away
77 pinto, weekend warrior
92 grand marquis, daily