Current Classifieds

1972 pinto grill
Date: 02/27/2018 12:13 am
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
C-3 automatic transmission

Date: 08/17/2022 10:18 am
73 rear hatchback glass
Date: 07/06/2017 11:33 am
I need a 1976 hood
Date: 12/19/2016 06:02 pm
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
looking for parts
Date: 06/19/2020 02:32 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
1980 hood needed
Date: 04/23/2020 10:41 pm
Dumping '80 yellow Pinto

Date: 06/21/2017 03:45 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
4:11 gears for 6.75 Make offer...NEED GONE

Date: 08/01/2018 01:27 pm

« previous next »
Pages: [1]   Go Down

Author Topic: 1977 Pinto V6 T-stat  (Read 2516 times)

0 Members and 1 Guest are viewing this topic.

Offline totljeep

  • Pinto Member
  • **
  • Posts: 59
  • FeedBack: +1/-0
  • Gender: Male
  • GIMME A TURBO!

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Fifth year Anniversary
1977 Pinto V6 T-stat
« on: October 04, 2013, 03:56:54 PM »
Can someone please tell me how to find and change the thermostat on this '77 w/2.8 V6. It's running hot so I'm gonna start there. Thanx a heap..
Logged
FIX MY PINTO ELSE I'LL DRIVE IT LIKE IT IS!

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 1977 Pinto V6 T-stat
« Reply #1 on: October 05, 2013, 12:47:12 PM »
On the v6, I believe they're located at the bottom front of the motor.

Here's a link with info: http://www.fordpinto.com/general-pinto-talk/running-warm/msg27994/#msg27994
Logged

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #2 on: October 05, 2013, 01:55:21 PM »
The thermostat is at the lower radiator hose. The housing is located in front of the water pump. There are three 10mm headed bolts holding it on. They thread into a 90 degree bypass nipple behind the timing cover.You will need a new thermostat, flat rubber gasket, housing gasket, nipple gasket. Its a bit tricky getting it all in place to bolt together.You said its running hot. How hot? I have had mine since new and it most always runs at the high end of normal on the factory gauge. 
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline totljeep

  • Pinto Member
  • **
  • Posts: 59
  • FeedBack: +1/-0
  • Gender: Male
  • GIMME A TURBO!

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #3 on: October 05, 2013, 09:29:07 PM »
Quote from: flash041 on October 05, 2013, 01:55:21 PM
The thermostat is at the lower radiator hose. The housing is located in front of the water pump. There are three 10mm headed bolts holding it on. They thread into a 90 degree bypass nipple behind the timing cover.You will need a new thermostat, flat rubber gasket, housing gasket, nipple gasket. Its a bit tricky getting it all in place to bolt together.You said its running hot. How hot? I have had mine since new and it most always runs at the high end of normal on the factory gauge. 
I don't have a temp gauge so I don't know exactly how hot but the coolant is boiling through the hose at the cap so I also installed a new rad cap.
Logged
FIX MY PINTO ELSE I'LL DRIVE IT LIKE IT IS!

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #4 on: October 06, 2013, 08:10:12 AM »
Had to replace my fan to get my b6 to run cooler, can run a/c on hot fl days or it gets to hot for me to be ok with sure the car would be ok but don't want to blow motor! Good luck n hope u fund your over hearing issue
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline totljeep

  • Pinto Member
  • **
  • Posts: 59
  • FeedBack: +1/-0
  • Gender: Male
  • GIMME A TURBO!

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #5 on: October 07, 2013, 08:52:37 PM »
What is the purpose of the small hose to the T-Stat housing? There is no opening for coolant to flow. Anyone know?
Logged
FIX MY PINTO ELSE I'LL DRIVE IT LIKE IT IS!

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #6 on: October 07, 2013, 09:29:53 PM »
The small hose ,5/8 dia, is the heater hose. dont know what you mean by" no opening for coolant to flow" unless it is corroded shut.
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 1977 Pinto V6 T-stat
« Reply #7 on: October 08, 2013, 09:16:09 AM »
You'll want to clear that hose fitting out. Could be part of your issue. You might want to check all your other connections for clogs, and then run a couple cycles of 'Super Cooling System Flush' through it. Sounds like it may have been neglected by a PO at some point.

Good luck!
Logged

Offline totljeep

  • Pinto Member
  • **
  • Posts: 59
  • FeedBack: +1/-0
  • Gender: Male
  • GIMME A TURBO!

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Fifth year Anniversary
Re: 1977 Pinto V6 T-stat
« Reply #8 on: October 09, 2013, 11:39:40 AM »
I'm pretty sure a head gasket is the problem. Will a 2.8 from a 1984 Ranger swap in place or is there any difference?
Logged
FIX MY PINTO ELSE I'LL DRIVE IT LIKE IT IS!
Pages: [1]   Go Up
« previous next »