Current Classifieds

Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
Many Parts Listed Below
Date: 04/20/2018 11:15 am
I'm looking for a 78 or older Pinto near Alberta
Date: 08/13/2021 10:39 am
Mustang ll/Pinto/Bobcat Aluminum Wheel Rim

Date: 07/20/2018 03:00 pm
1978 Squire wagon 6 Cly
Date: 03/08/2021 10:44 am
1971-1975 Pinto
Date: 01/09/2017 04:14 pm
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
72 Turbo Pinto "Hot Rod" rebuild
Date: 08/09/2018 11:09 am
1977 Pinto for parts

Date: 10/10/2018 06:25 pm
76 Pinto Wagon
Date: 07/08/2020 05:44 pm
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
Pangra wanted
Date: 02/05/2017 01:58 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Port hole windows  (Read 1415 times)

0 Members and 1 Guest are viewing this topic.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Port hole windows
« on: August 19, 2017, 03:00:02 PM »
I'm pretty sure these rings just pull out but I want to make sure. Since parts are so hard and expensive I just want to check.


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #1 on: August 20, 2017, 04:55:28 PM »
Ok so I may be wrong I tried taking off the inside bezel by just pulling on it. It's not budging   Do I have to take the whole thing apart?


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Pintopower

  • PCCA Management Board
  • Pinto Sr. Member
  • ******
  • Posts: 720
  • FeedBack: +92/-0
  • Gender: Male
  • Why a Pinto? Because I don't care what you think.
    • My Car Pictures

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Photographer Windows User Webmaster Tenth year Anniversary Fifth year Anniversary
Re: Port hole windows
« Reply #2 on: August 21, 2017, 02:51:39 PM »
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Logged
I have many Pintos, I like them....
#1. 1979 Wagon V6 Restored
#2. 1977 Wagon V6 Restored
#3. 1980 Sedan I4 Original
#4. 1974 Pangra Wagon I4 Turbo
#5. 1980 Wagon I4 Restored
#6. 1976 Bobcat Squire Hatchback (Restoring)
...Like i said, I like them.
...and I have 4 Fiats.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #3 on: August 21, 2017, 04:02:00 PM »
Good idea I will give it a try. I am just a little cautious because parts are so hard to find. Thanks so much


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #4 on: August 24, 2017, 01:04:50 PM »
Quote from: Pintopower on August 21, 2017, 02:51:39 PM
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Thanks
What I did was put Dawn and water in a spry bottle. The sprayed the rubber seal and they came right out.


Sent from my iPhone using Tapatalk
Logged
Joe
Pages: [1]   Go Up
« previous next »