Current Classifieds

72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
Automatic Wagon
Date: 06/14/2019 11:22 pm
Free 2.0L Valve Cover

Date: 01/03/2023 04:27 pm
1973 Ford Pinto Squire Wagon 3 Door

Date: 07/11/2023 11:39 pm
72 Runabout for Sale- Washington

Date: 02/28/2024 02:07 pm
 Alloy Harmonic Balancer

Date: 07/10/2020 12:17 pm
Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am

« previous next »
Pages: [1]   Go Down

Author Topic: '79 ballast resistor  (Read 1403 times)

0 Members and 1 Guest are viewing this topic.

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
'79 ballast resistor
« on: April 15, 2017, 06:30:50 PM »
I had some burned wires at the voltage regulator. I repaired them being careful to splice the new wire into the connector one wire at a time.
The engine runs with key in start.  When key is released, it dies.  I don't know where the ballast resistor is and want to check if is good.
Can somebody help me with the ballasted thing!

Enzo.
Logged

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: '79 ballast resistor
« Reply #1 on: April 15, 2017, 07:46:14 PM »
The ballast resistor is behind the speedometer, it's a special wire with plug ends on each end , but I would check the plug at the ign module before you start removing things ,  you have a two wire plug with a red and white wire , one is hot when you turn on the ign switch , the other is a bypass from the start solenoid that bypasses the resistor to keep the voltage up when cranking , look for corrosion in the plug , (green ) if no volts with key on , bad switch or as you say bad resistor , (rare)  also could be a bad box , if it is org they had problems back in 75 to late 76 , look for a blue tab one the box where the wire come out , that was the fix back hem , later Blaine
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: '79 ballast resistor
« Reply #2 on: April 15, 2017, 11:01:17 PM »
Blaine,  Thanks for the info. I failed to mention that this is a 2.3, not that should make much difference. Will look into that.
Took a break from the car. 
Worked all day (9:30-5:00, no meals) swapping alternators, ECU's, regulators, triple checking connectors, triple checking wiring, checking for slipped timing, and, fuel supply. I even changed the ignition switch. Nothing!!!  I'm lost. I don't know what I did wrong, but, it won't run.  I will start up tomorrow early as this my daily driver.  Thinking about getting a later model of something for daily.
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: '79 ballast resistor
« Reply #3 on: April 15, 2017, 11:44:08 PM »
Oh!! Man!!  I even got sunburned today, on my face and of course the top of my head, from being outside so long here in the Pacific NW.

Have good weekend everybody.
Logged

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: '79 ballast resistor
« Reply #4 on: April 19, 2017, 08:58:56 AM »
Thanks Blaine for the help.  Not sure I would have found all the problems.
New regulator and alternator and everything works.
Logged

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: '79 ballast resistor
« Reply #5 on: April 19, 2017, 11:34:48 PM »
No problem , glad I could help you , later Blaine
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0
Pages: [1]   Go Up
« previous next »