Current Classifieds

1971 Pinto Runabout turn key driver

Date: 12/04/2018 07:40 pm
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
78 wagon instrument y
Date: 04/30/2018 07:41 pm
Pinto 4-spd transmissions
Date: 06/15/2018 09:15 am
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
Pinto drive train

Date: 06/29/2018 08:32 am
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
1978 pinto grill
Date: 07/24/2018 02:18 pm
78 windshield trim
Date: 02/01/2020 08:46 am
Early 2.0 engines
Date: 05/09/2018 12:45 pm
77 Cruising wagon Rear cargo light
Date: 10/02/2017 02:16 pm

« previous next »
Pages: [1]   Go Down

Author Topic: What are ya'll doing for intercoolers?  (Read 3647 times)

0 Members and 1 Guest are viewing this topic.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
What are ya'll doing for intercoolers?
« on: May 30, 2014, 06:11:26 PM »
I searched. Believe me, I search before starting a new thread. ;D

I'm still gathering info for my 2.3T swap. The engine I have is out an '86 'Bird, so it's not intercooled and I will likely run it that way for a while. However, I want to unlock the full 205hp potential of the setup and that means using an IC. I have an '87-88 'Bird IC that might be useful with custom tanks.

Catch #1: I want to avoid cutting up the radiator support, so that means routing tubes through the big oval hole on the passenger side, which means an intercooler with in/out on the same side.

Catch #2: I want to fit an A/C condenser somewhere between the grille and radiator too. I was thinking about an intercooler on one side and a condenser on the other rather than placing one in front of the other as is usually done. I haven't yet looked to see what sizes and shapes of condensers are available and/or suitable.

Anyone with experience or ideas doing something similar? Suggestions, critique, etc are welcome.
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline don33

  • Pinto Sr. Member
  • ****
  • Posts: 280
  • FeedBack: +5/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Fifth year Anniversary Poll Voter Windows User
Re: What are ya'll doing for intercoolers?
« Reply #1 on: June 01, 2014, 06:53:43 PM »
I cut the rad support, But, I'm pretty sure you can use the Large NPR IC. without cutting, it is a pretty good IC, works Well... I like the NPR because its well designed for a minimal IC tubing setup.
Logged

Offline Bigtimmay

  • Pinto Sr. Member
  • ****
  • Posts: 710
  • FeedBack: +8/-0
  • Gender: Male
  • Everythings better with boost!

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Fifth year Anniversary Mobile User Windows User
Re: What are ya'll doing for intercoolers?
« Reply #2 on: June 05, 2014, 01:44:22 PM »
you have to cut the rad support some to put in a npr for where the tubes run through but you can keep the top of the support and the hood latch and all that stuff. and a npr bolts in the same spot as the radiator.
Logged
1978 Mercury Bobcat 2.3t swapped.Always needs more parts!

Offline L.D

  • Pinto Member
  • **
  • Posts: 46
  • FeedBack: +16/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Windows User Linux User Mobile User
Re: What are ya'll doing for intercoolers?
« Reply #3 on: June 10, 2014, 11:39:12 PM »
what year and size of npr intercoolers are you guys running?
Logged
Pages: [1]   Go Up
« previous next »