Current Classifieds

1972 Rallye wagon rebuild
Date: 11/14/2020 07:31 pm
WTB Manual Transmission Clutch Pedal for '78
Date: 03/29/2019 07:20 am
pro stock front end
Date: 06/28/2019 07:43 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
WTB: 2.0 Mech tach drive distributor
Date: 04/14/2023 06:15 am
Custom Pinto Project

Date: 06/12/2016 07:37 pm
1974 Wiring diagram free
Date: 10/27/2019 06:56 pm
1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
Parts Parts Parts
Date: 09/08/2018 03:13 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/28/2018 09:37 am

« previous next »
Pages: [1]   Go Down

Author Topic: Exhaust manifold to convertor upper bolt  (Read 1141 times)

0 Members and 1 Guest are viewing this topic.

Offline r4pinto

  • Pinto PooBAH
  • ******
  • Posts: 3854
  • FeedBack: +108/-0
  • Gender: Male
  • All hail Ford Pinto!!!!

    • Total Badges: 9
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Mobile User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Exhaust manifold to convertor upper bolt
« on: August 09, 2015, 06:47:45 PM »
Got a quick question.. Hopefully someone has had the same issue lol. On my 80 Pinto I'm trying to remove the manifold to convertor bolt so I can get the manifold out of the way, so I can pull the engine, as well as replace the old gasket. I was able to get the lower bolt out but can't get a wrench on the upper bolt. Any ideas on how to remove it?
Logged
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress

Offline postalpony

  • Pinto Full Member
  • ***
  • Posts: 201
  • FeedBack: +30/-0
  • Gender: Male
  • WHEN IN DOUBT--BUILD IT STOUT!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary Photographer
Re: Exhaust manifold to convertor upper bolt
« Reply #1 on: August 09, 2015, 09:22:06 PM »
Matt  Try a socket with a universal & long extention--may work.
Good luck.
Logged
1980 Hatchback was a "Postal Unit" on the
west coast in it's early life. Now residing
in Ohio, But we don't haul the U.S. Mail anymore;
 Now all we do is HAUL!
 5th gear 4700 rpm & still pullin'= 113+  mph
 
 UPDATE-83.762 mph in 4th gear As verified by a W Va State Trooper-WITH 1 GEAR TO GO 6-2-11

Offline r4pinto

  • Pinto PooBAH
  • ******
  • Posts: 3854
  • FeedBack: +108/-0
  • Gender: Male
  • All hail Ford Pinto!!!!

    • Total Badges: 9
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Mobile User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Exhaust manifold to convertor upper bolt
« Reply #2 on: August 09, 2015, 09:55:25 PM »
Thanks Dick, couldn't hurt to try. I gotta jack up the right side of the car anyway so I can change the tires out with the 77s, as well as disconnect the driveshaft from the transmission so I'll try that then.
Logged
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress
Pages: [1]   Go Up
« previous next »