Author Topic: The little plastic spacers for the leaf springs?  (Read 1952 times)

0 Members and 1 Guest are viewing this topic.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
The little plastic spacers for the leaf springs?
« on: November 12, 2014, 12:15:55 PM »
Does anybody sell these things?
And, just what are they for? Just spacers, or for noise reduction?
I can re-use the ones I have, but I would rather get new since I am going to all the trouble of blasting and repainting the springs.
Thanks,
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline Pinto1600

  • Coordinator of the 'Carlisle 40th'
  • PCCA Management Board
  • Pinto Full Member
  • ******
  • Posts: 235
  • FeedBack: +50/-0
  • Gender: Male
  • Carlisle '08

  • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Mobile User Poll Voter Apple User Windows User Fifth year Anniversary
Re: The little plastic spacers for the leaf springs?
« Reply #1 on: November 12, 2014, 02:26:09 PM »
The spacers are anti-squeak/spring sliders. I don't know of anybody who has them as replacements. You could make them if you can find the right material. Good luck on the project.
Happiness is..Driving a classic Pinto

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: The little plastic spacers for the leaf springs?
« Reply #2 on: November 12, 2014, 02:59:15 PM »
you need what they call leaf spring pads , they go in the square hole at each end , they cost a little over a buck each and you can find them on e bay or any spring re-arch shop,  but if your springs have any deep rust spots it will crack and brake there, replace in sets and not just one , JC Whitney had a set for my saggy pinto cruiser Wagon
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: The little plastic spacers for the leaf springs?
« Reply #3 on: November 12, 2014, 03:08:29 PM »
My Sunbeam Tiger had circular indents in the spring. I used faucet washers and packed the center hole with grease. Sadly it is year 15 and it is still on jackstands so I can't tell how well they work.  :(

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: The little plastic spacers for the leaf springs?
« Reply #4 on: November 12, 2014, 08:08:46 PM »
I have even left the spacers completely off before and no noise issues at all.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: The little plastic spacers for the leaf springs?
« Reply #5 on: November 13, 2014, 08:27:27 PM »
Thanks,
I guess I can just reuse the old ones.
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: The little plastic spacers for the leaf springs?
« Reply #6 on: November 21, 2014, 08:14:32 AM »
I may have found a source for these.
I have ordered some and will let you all know if they are the right size.
Thanks,
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: The little plastic spacers for the leaf springs?
« Reply #7 on: November 21, 2014, 09:24:05 AM »
Speedway has them in their street rod catalog.
Its better to be a has-been, than a never was.