Current Classifieds

NOS Sedan decklid

Date: 10/23/2019 11:51 am
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
71 72 front bumper brackets
Date: 06/10/2020 10:55 am
need intake for oval port 2.3l
Date: 08/22/2018 09:23 am
1980 hood needed
Date: 04/23/2020 10:41 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
1972 pinto grill
Date: 02/27/2018 12:13 am
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
Various Pinto Parts 1971 - 1973

Date: 10/01/2020 02:00 pm
Looking for a Single Stage Nitrous Kit/ 2-bbl Holley Spray Bar Plate
Date: 01/06/2017 11:42 pm

Author Topic: Question for the 302 V8 builders!!!  (Read 3680 times)

0 Members and 1 Guest are viewing this topic.

Offline mrpinto

  • Pinto Full Member
  • ***
  • Posts: 186
  • FeedBack: +0/-0
  • Gender: Male
  • This ain't yer Gramma's Pinto!

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Fifth year Anniversary Photographer
Question for the 302 V8 builders!!!
« on: October 17, 2006, 07:41:58 PM »
I'm going to be rebuilding my engine this winter, and I've been thinking of installing a stroker kit. I don't know a whole lot about engine building, but with the help of a friend with a bit of experience and a few manuals, I should be able to get the job done. 
Anyway,I have been told that if I plan on driving the car regularly, which I do, to not stroke to 347ci because of oil consumption and decreased reliability. Instead, I've been told  instead to stroke to 331ci.

Anyone have any input, or experience regarding stroking the 302? Is it worth the cost?


I have come across this 331 stroker kit on Ebay, and the price seems great, but I'm not familiar with any of the componants. If someone can take a look and offer any advice it'd be greatly appreciated.

Thanks in advance.


http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=007&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=170039750354&rd=1&rd=1
1979 302 Pinto Custom
1971 460 Drag Pinto

Offline 78pinto

  • Chief Moderator-Retired
  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1918
  • FeedBack: +96/-0
  • Gender: Male
  • Twin Turbocharged
    • The Red Rocket

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter 1000 Posts Webmaster Tenth year Anniversary Fifth year Anniversary
Re: Question for the 302 V8 builders!!!
« Reply #1 on: October 17, 2006, 09:05:14 PM »
Most kits nowadays don't have rings that intersect with the pins....that cause the oil problems, however....if it was me i'd build a 331 or 327 stroker for street use.  The long stroke/rod tends to put alot of pressure on the piston skirt and can cause premature wear/scuffing leading to eventual skirt failure/piston slap.  Don't be cheap with internal componets...us e brand name stuff, Eagle, Scat ect. Alot of the cheaper parts made by offshore/China GENERALY will require machining due to nasty tolerances/craftmaship.  A cast nodular steel crank will be fine, but use good rods (h-beam or I-beam) and good pistons (forged if any kinda power adder will be used....nitrou s) hope that helps.   Jeff 
** Jeff (78Pinto) is Missing from us but will always be a part of our community- We miss you Jeff **

Offline BigMike

  • Pinto Driver
  • *
  • Posts: 1
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary
Re: Question for the 302 V8 builders!!!
« Reply #2 on: November 26, 2006, 05:01:31 PM »
Hi there nothing wrong with the building a 347 stroker I have built many 347's in the past for friends and my self i never put one in a pinto my pinto i went with a boss 429 big block but i did build a 347 for my 89 t-Bird and my 95 mustang and they work very well there ready made kits for them from ford it self also from jeg's and summit and the fact is they most planty full kits the 308,327, and 331 are harder to find