Current Classifieds

FLOOR PANS
Date: 06/12/2020 07:24 pm
1977 Cruiser
Date: 06/29/2019 06:28 am
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Great Cruise wagon

Date: 12/17/2016 03:39 pm
1973 Pangra

Date: 01/06/2015 02:19 pm
TWM Intake
Date: 08/15/2018 08:20 pm
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
wanted a 1979 Pinto or Bobcat front valance
Date: 03/17/2019 10:15 pm
WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm

Author Topic: Mini Starter 2.3  (Read 1370 times)

0 Members and 1 Guest are viewing this topic.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Mini Starter 2.3
« on: November 24, 2015, 01:27:21 PM »
I recall someone stating that the Ranger had a mini starter from the factory. Is this true? If so is there anything special to know about them? In my application it would be an '88, 2.3, 5 speed.

My interest is that the original starter is too low when I adapted the 2.3 (Turbo) into my '73 Pinto. The lower portion of the starter hits the back rack bolt on its hold down strap. And..., the rear bearing protrusion barely fits into the indent area of said strap (see image).

So, in addition to the smaller diameter of a mini starter being a plus for the strap bolt, I was hoping it was a bit shorter too. Can anyone confirm this?

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Mini Starter 2.3
« Reply #1 on: November 24, 2015, 06:56:24 PM »
I used one from a 95 ranger on my 76 pinto wagon that went underwater during Katrina, still have the car and can take photos of the starter , I do believe it's shorter, so I will bring a tape and find out , later Blaine

76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Mini Starter 2.3
« Reply #2 on: November 24, 2015, 07:24:47 PM »
The mini starter is about a 1/2" shorter.  Good to hear they work with the early 2.3.  I have seen mixed info on tooth count compatibility.
Jerry J - Jupiter, Florida

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Mini Starter 2.3
« Reply #3 on: November 24, 2015, 09:09:30 PM »
Thanks. Half an inch will seem like a mile given the feeler gauge like clearance I have now.  Not sure how all these years I've missed this upgrade.  I've cut a notch in the rack rubber and then bent inward the strap. I ground the top off the strap bolt as far as I could and still had something to tighten. Still I get the engine on metal rattle just going over a bump in the road. Looking forward to this change.  I guess it is the price to be paid for using the factory intercooler and the stock hood - less the air intake. Well until I get the starter changed.  :)

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Mini Starter 2.3
« Reply #4 on: November 25, 2015, 05:45:09 AM »
They work great , I also put one one my V6 pinto , it came off a 4.0 Explorer , spins the crap out the engine ,
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline RICO2

  • Pinto Member
  • **
  • Posts: 10
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Mobile User Windows User
Re: Mini Starter 2.3
« Reply #5 on: November 27, 2015, 04:45:55 AM »
JUST BY CHANCE WOULD THIS MINI STARTER WORK ON A 302 , IM DOING A CONVERSION PROJECT AND IF THIS WOULD WORK WOULD BE GREAT FOR SOME EXTRA CLEARANCE ISSUES THAT MIGHT ARISE. ?