Current Classifieds

'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
1971 Pinto instrument cluster clear bezel WTB
Date: 03/16/2017 10:00 pm
Wanted 73 pinto squire wagon
Date: 05/09/2020 11:59 am
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
2 Station Wagons for sale
Date: 04/20/2018 11:10 am
NOS Sedan decklid

Date: 10/23/2019 11:51 am
ENGINE COMPLETE 1971 PINTO
Date: 12/28/2017 03:55 pm
Wanted Postal Pinto
Date: 08/30/2021 03:20 pm
Seeking parts
Date: 10/18/2020 10:35 am
Pinto Fiber Glass Body Parts
Date: 01/06/2019 06:53 pm
WTB - 1979 Fan Shroud - D52E-8246-CIB
Date: 11/05/2020 06:32 pm

Author Topic: Rear end gear ratios  (Read 1919 times)

0 Members and 1 Guest are viewing this topic.

Offline popbumper

  • Pinto Master
  • *****
  • Posts: 1919
  • FeedBack: +100/-1
  • Gender: Male

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Mobile User Poll Voter Windows User 1000 Posts Fifth year Anniversary
Rear end gear ratios
« on: February 13, 2015, 09:55:20 AM »
Can anyone tell me what the factory gear ratios were for the following rear ends?

1976 wagon MPG model with 2.3L, 6.75" rear end
1978 glass hatch V6 model 8" rear end (white car with red accents, factory mags and center caps) - I think this was a package

Thank you!

Chris
Restoring a 1976 MPG wagon - purchased 6/08

Offline jonz2pinto

  • Pinto Member
  • **
  • Posts: 83
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Linux User Mobile User
Re: Rear end gear ratios
« Reply #1 on: February 13, 2015, 10:27:02 AM »
I have had 76 hatch 8" w/3.40 and 77 wagon 8" w/3.08.The 6.75 rears in sedans I had 3.08 s.
Pinto-is short for pint-o-fun.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Rear end gear ratios
« Reply #2 on: February 13, 2015, 10:31:08 AM »
Easy to check. Turn the brake drum one turn and count the number of times the drive shaft turns. One turn of the drum and three turns of the yoke would be 3:00 X 1.  I learned this from a Vega owner when he was trying to see how far he could go before the engine would blow up.
Its better to be a has-been, than a never was.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Rear end gear ratios
« Reply #3 on: February 13, 2015, 12:53:40 PM »
Been there, done that. Though I will say with driveline slop the difference between say... 3.40 and 3.55 can, at times, be hard to discern. The 8" "should have a tag showing the ratio.  When I would go to Pick A Part looking for an 8" rear I would always write in the dust on the rear glass the ratio - helps out the next guy from having to crawl under.

  Once I tried to detect the 1st gear ratio of a Jeep Toploader. I had to crank over that V-8 engine by hand over three times before I could detect that it WASN'T the T-178 transmission I was hoping it was. I was more doing pull-ups under the Jeep than I was getting rotation.