Current Classifieds

Mustang II C4 Transmission
Date: 07/28/2017 06:26 am
Bumper Guards
Date: 03/28/2017 09:27 pm
79 pinto small parts
Date: 04/24/2019 03:16 pm
Seeking parts
Date: 10/18/2020 10:35 am
SVO SWAP
Date: 03/15/2018 03:12 am
Wanted Type 9 5spd Transmission
Date: 07/04/2017 03:26 pm
Various Pinto Parts 1971 - 1973

Date: 10/01/2020 02:00 pm
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am
Wanted Postal Pinto
Date: 10/26/2020 03:24 pm
76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm

Author Topic: Front Rim Offset for 15 inch conversion....  (Read 1230 times)

0 Members and 1 Guest are viewing this topic.

Offline niceguynnc

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Gender: Male
  • Proud 1976 Runabout owner.

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Linux User Mobile User Windows User
Front Rim Offset for 15 inch conversion....
« on: February 10, 2015, 03:14:13 PM »
I just drilled my rear axles to 5x4.5 and ordered the rotor kit for the front to adapt to 5x4.5.  My car is stock and not tubbed. I know the front ball joint is tricky on these cars and the offset has to be right. Also the center circle has to be right too! I want 8 inch wide on the rear and 6 inch on the front. Anyone with 15 inch wheels that can help me get a rim order right i would really appreciate it. Summit could not help me at all.... I am looking at the 4 .5 backspacing on the rear. And as far as the front I have no idea on backspacing due to going to the 15 inch rim diameter..I really want to get the order right the first time. ANY help would be appreciated to the fullest extent! Thanks again in advance!! Greg.

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Front Rim Offset for 15 inch conversion....
« Reply #1 on: February 19, 2015, 10:28:02 PM »
Go to "Wheel Vintiques.com", page 47.  There is a wheel fitment guide that will show where you need to measure.  I also recommend measuring with a straight edge from the face of the rotor where the wheel contacts the rotor to the outermost edge of the top a-arm. That is also a potential contact point of the wheel lip if your backset is too deep.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Front Rim Offset for 15 inch conversion....
« Reply #2 on: February 20, 2015, 08:03:07 AM »
Anything more than 3 3/4" will drag on the upper control arm. With a 15 X 6 wheel I would go with 2" to 3" back space. 2" would be what I think would fill up the wheel well with that narrow a wheel. If you use too much back space the wheel will look like it came off a FWD car. LOL
Its better to be a has-been, than a never was.