Current Classifieds

Windshield
Date: 01/15/2022 09:31 pm
Wanted - Offenhauser intake for 2.8l (6097DP)
Date: 01/28/2019 05:15 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
Pinto Parts Windows & Windshield

Date: 11/12/2020 08:28 pm
C-3 automatic transmission

Date: 08/17/2022 10:18 am
1977 Pinto Cruizin Wagon

Date: 08/07/2023 02:52 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
Looking for leaf spring insulators
Date: 04/04/2020 09:38 am
71-73 sway bar
Date: 06/12/2021 10:12 am
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
Looking for front seats
Date: 08/10/2021 09:54 pm

Author Topic: Valve lash  (Read 4744 times)

0 Members and 1 Guest are viewing this topic.

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Valve lash
« on: July 15, 2009, 05:26:04 PM »
Ok, I'm a little stuck here on this one i have a Chiltons manual american cars from 1966 to 1973 book thats REALLY REALLY OLD and i treat it as if its my bible which it is :D but its not very specific. it says under valve clearance adjustment 2000cc engine-set cold: Valves to adjust to depressed
             .008    .010
   No.1     No.6     No.7
   No.2     No.8     No.3
   No.3     No.2     No.5
   No.5     No.4     No.1


 So im a bit confused from this diagram it shows, can someone elaborate further?


Thanks!
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Valve lash
« Reply #1 on: July 16, 2009, 05:15:23 AM »
The simplest method is to rotate the engine until the lobe is up and then check that valve's clearance (between the lobe and the follower rocker).  For the stock cam, the cold clearances are 0.008" intake and 0.010" exhaust.

I have not tried it but that table will save some effort by minimizing the engine rotations.  Per the 1974 Ford manual, number the cam lobes 1 thru 8 front to back.  Rotate the engine until the number 1 lobe is down (valve compressed) then set the #6 clearance at 0.008" (intake) and the #7 clearance at 0.010" (exhaust).  Continue down the table until all valves are adjusted.
Jerry J - Jupiter, Florida

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Re: Valve lash
« Reply #2 on: July 16, 2009, 01:52:34 PM »
OH! i knew that...my car is a '73
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto