Current Classifieds

Pinto wagon Parts
Date: 06/23/2021 03:25 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
Wanted Pinto Fiberglass Body Parts
Date: 08/16/2018 08:54 am
71-73 Hood
Date: 12/07/2018 06:22 pm
Misc. Pinto parts

Date: 11/09/2019 04:25 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
Sunroof shade
Date: 06/19/2019 01:33 pm
1979 Pinto 3-door Runabout *PRICE REDUCED*

Date: 08/01/2023 06:53 pm
Pinto sales literature / magazine ads/ owners manuals
Date: 03/21/2017 07:47 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Valve lash  (Read 4747 times)

0 Members and 1 Guest are viewing this topic.

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Valve lash
« on: July 15, 2009, 05:26:04 PM »
Ok, I'm a little stuck here on this one i have a Chiltons manual american cars from 1966 to 1973 book thats REALLY REALLY OLD and i treat it as if its my bible which it is :D but its not very specific. it says under valve clearance adjustment 2000cc engine-set cold: Valves to adjust to depressed
             .008    .010
   No.1     No.6     No.7
   No.2     No.8     No.3
   No.3     No.2     No.5
   No.5     No.4     No.1


 So im a bit confused from this diagram it shows, can someone elaborate further?


Thanks!
Logged
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Valve lash
« Reply #1 on: July 16, 2009, 05:15:23 AM »
The simplest method is to rotate the engine until the lobe is up and then check that valve's clearance (between the lobe and the follower rocker).  For the stock cam, the cold clearances are 0.008" intake and 0.010" exhaust.

I have not tried it but that table will save some effort by minimizing the engine rotations.  Per the 1974 Ford manual, number the cam lobes 1 thru 8 front to back.  Rotate the engine until the number 1 lobe is down (valve compressed) then set the #6 clearance at 0.008" (intake) and the #7 clearance at 0.010" (exhaust).  Continue down the table until all valves are adjusted.
Logged
Jerry J - Jupiter, Florida

Offline delizious

  • Pinto Member
  • **
  • Posts: 82
  • FeedBack: +0/-0
  • Gender: Female

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Windows User Fifth year Anniversary
Re: Valve lash
« Reply #2 on: July 16, 2009, 01:52:34 PM »
OH! i knew that...my car is a '73
Logged
Lost 1972 Ford Pinto
Gained 1978 Ford Pinto
Pages: [1]   Go Up
« previous next »